Turnstile gate
ttaqinmu·turnstile-gate·kicad/control-board/control-board.kicad_pcb
About the Turnstile gate PCB
Turnstile gate is an open source ESP32 PCB design by ttaqinmu, published on GitHub. It is a 2-layer board measuring 115 × 95 mm, with 14 components from 14 distinct parts.
Its main chip is the ESP32 J2, from the ESP32 family. Other key parts include the PC817. By type, the board carries 8 connectors, 5 resistors and 1 IC.
It belongs with the power & battery and sensors designs in this gallery.
From the project
Open the KiCad layout · Preview · DRC report
Open the KiCad layout · Preview · DRC report
This 115 × 95 mm, two-layer PCB is a carrier for the ESP32-DevKitC V4 with an ESP32-WROOM module. It holds two 19-pin sockets, a PC817, a 330 Ω/0.5 W resistor, four 10 kΩ pull-ups, signal terminals, and four M3 mounting holes. PCB traces are 0.30 mm wide. An external buck converter supplies 5 V.
The PCB carries only 5 V, 3.3 V, and signals. The 24 V supply, fuses, emergency stop, power-cut relay, motor driver, power capacitor, motor, and IR sensor supply are installed in the panel according to the system schematic. The PCB's IR terminal carries…
Main components on the Turnstile gate
Turnstile gate bill of materials (BOM)
14 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PC817 | DIP-4_W7.62mm | U5 |
| 1 | 5V BUCK | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | QR UART | TerminalBlock_Phoenix_MKDS-1,5-4-5.08_1x04_P5.08mm_Horizontal | J2 |
| 1 | MOTOR DRIVER LOGIC | TerminalBlock_Phoenix_MKDS-1,5-4-5.08_1x04_P5.08mm_Horizontal | J3 |
| 1 | IR RELAY COM NO | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J4 |
| 1 | LIMIT HOME NC | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J5 |
| 1 | LIMIT OPEN NC | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J6 |
| 1 | ESP32 J2 | PinSocket_1x19_P2.54mm_Vertical | J7 |
| 1 | ESP32 J3 | PinSocket_1x19_P2.54mm_Vertical | J8 |
| 1 | 330R 0.5W | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R1 |
| 1 | 10k IR | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 10k HOME | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 10k OPEN | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 10k FLT | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
Turnstile gate design files
The KiCad project lives in the ttaqinmu/turnstile-gate repository on GitHub; these links point at the commit this page was built from.
Turnstile gate: common questions
What microcontroller does the Turnstile gate use?
The Turnstile gate is built around the ESP32 J2, from the ESP32 family.
How big is the Turnstile gate PCB?
The Turnstile gate measures 115 × 95 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Turnstile gate?
14 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Turnstile gate design files?
From the ttaqinmu/turnstile-gate repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Turnstile gate design in my own project?
The repository has no license, so all rights stay with ttaqinmu. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Turnstile gate without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k