Termite keyboard

turtureanu·termite-keyboard·pcb/termite.kicad_pcb

Termite keyboard PCB layout, top view — open source RP2040/RP2350 board by turtureanu

About the Termite keyboard PCB

Termite keyboard is an open source RP2040/RP2350 PCB design by turtureanu, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 128.2 × 82.1 mm, with 110 components from 7 distinct parts.

Its main chip is the Pico, from the RP2040/RP2350 family. By type, the board carries 36 LEDs, 34 switches, 34 diodes, 2 ICs, 2 connectors and 2 resistors.

It belongs with the keyboards and displays & leds designs in this gallery.

From the project

A simple 34-key ortholinear dual OLED low profile mechanical keyboard.

This is a 34-key ortholinear split keyboard with built-in wrist supports, one 0.91" OLED display on each half, and low-profile mechanical Cherry-MX type switches (Gateron). I use a TRRS cable to connect the two halves. The case is 3D printed and uses 5 M2 screws (four M2x12, one M2x4).

I created this keyboard as a replacement for my laptop's keyboard, which might fail soon. I wanted an ortholinear split keyboard with fewer keys that would fit the Engram keyboard layout. In the past I designed a similar keyboard with an 0.42" OLED display under each key (inspired by PolyKybd Split 72), but I…

Termite keyboard, from the project README
From the project README

Main components on the Termite keyboard

Termite keyboard bill of materials (BOM)

110 components, 7 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
Pico
U1, U2
2
AudioJack4
J1, J2
34
SW_Push_45deg
SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +26
34
~
LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8 +26
2
SSD1306-0.91-OLED-4pin-128x32
OLED1, OLED2
34
1N4148
D1, D2, D3, D4, D5, D6, D7, D8 +26
2
4.7
R1, R2

Termite keyboard design files

The KiCad project lives in the turtureanu/termite-keyboard repository on GitHub; these links point at the commit this page was built from.

Termite keyboard: common questions

What microcontroller does the Termite keyboard use?

The Termite keyboard is built around the Pico, from the RP2040/RP2350 family.

How big is the Termite keyboard PCB?

The Termite keyboard measures 128.2 × 82.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Termite keyboard?

110 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Termite keyboard design files?

From the turtureanu/termite-keyboard repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Termite keyboard design in my own project?

Yes, under the terms of its GPL-3.0 license, which turtureanu chose for the repository.

Can I test firmware for the Termite keyboard without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards