Tuxtag hardware
TuxElectronics·tuxtag-hardware·pcb/tuxtag-pcb.kicad_pcb
About the Tuxtag hardware PCB
Tuxtag hardware is an open source ESP32 PCB design by TuxElectronics, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 25.8 × 37.2 mm, with 13 components from 8 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_TH, from the ESP32 family. By type, the board carries 4 diodes, 4 resistors, 3 connectors, 1 IC and 1 transistor.
It belongs with the iot & wireless designs in this gallery.
Main components on the Tuxtag hardware
Tuxtag hardware bill of materials (BOM)
13 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SUPERMINI_TH | MODULE_ESP32-C3_SUPERMINI_TH | U1 |
| 1 | P2N2222A | TO92 | Q1 |
| 1 | vibrator | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | battery | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | buzzer | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | 1N4148 | DO35-7 | D1 |
| 3 | OVLAW4CB7 | LEDRD254W50D305H520P | D2, D3, D4 |
| 4 | R | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2, R3, R4 |
Tuxtag hardware design files
The KiCad project lives in the TuxElectronics/tuxtag-hardware repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/tuxtag-pcb.kicad_pcb
Tuxtag hardware: common questions
What microcontroller does the Tuxtag hardware use?
The Tuxtag hardware is built around the ESP32-C3_SUPERMINI_TH, from the ESP32 family.
How big is the Tuxtag hardware PCB?
The Tuxtag hardware measures 25.8 × 37.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Tuxtag hardware?
13 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Tuxtag hardware design files?
From the TuxElectronics/tuxtag-hardware repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Tuxtag hardware design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which TuxElectronics chose for the repository.
Can I test firmware for the Tuxtag hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k