Shoe ctrl board

umass-hrsl·adjustable-compliance-footwear·PCB design/shoe_ctrl_board/shoe_ctrl_board.kicad_pcb

Shoe ctrl board layout, top view — open source AVR/Arduino board by umass-hrsl

About the Shoe ctrl board

Shoe ctrl board is an open source AVR/Arduino PCB design by umass-hrsl, published on GitHub under the MIT license. It is a 2-layer board measuring 82.6 × 76.6 mm, with 29 components from 24 distinct parts.

Its main chip is the Arduino Pro Mini, from the AVR/Arduino family. Other key parts include the L293D, SSCDANN100PGAA5 and NCV78M05BDTRKG. By type, the board carries 13 connectors, 6 ICs, 4 capacitors, 3 resistors and 2 switches.

From the project

Design files for ACFT

This repository contains the design files for the Adjustable Compliance Footwear Technology characterized in:

See the Bill of Materials spreadsheet for a complete list of materials required to build the system, including vendor links and prices as of Oct 2025.

See the CAD folder for Solidworks files for all parts of the assembly. Note that the midsole lattice files were created in Blender and must be unzipped.

Shoe ctrl board, from the project README
From the project README

Main components on the Shoe ctrl board

Arduino Pro MiniL293DSSCDANN100PGAA5NCV78M05BDTRKG

Shoe ctrl board bill of materials (BOM)

29 components, 24 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Arduino Pro Mini
U1
1
L293D
U3
3
SSCDANN100PGAA5
U4, U5, U6
1
NCV78M05BDTRKG
U7
1
RF_Receiv
J1
1
MicroSD
J2
1
HE_Sensor
J3
1
Exhaust1
J4
1
Exhaust2
J5
1
Cutoff1
J6
1
Cutoff2
J7
1
PumpDriver
J8
1
FSR1
J9
2
FSR2
J10, J11
1
Screw_Terminal_01x02
J12
1
I2C
J13
1
R_Potentiometer_US
RV1
1
SW_Push_Dual
SW1
1
SW_DIP_x01
SW2
2
0.1uF
C1, C3
Show 4 more
QtyPartRefs
1
C_Polarized
C2
1
0.33uF
C4
1
100k
R1
2
10k
R2, R3

Shoe ctrl board design files

The KiCad project lives in the umass-hrsl/adjustable-compliance-footwear repository on GitHub; these links point at the commit this page was built from.

Shoe ctrl board: common questions

What microcontroller does the Shoe ctrl board use?

The Shoe ctrl board is built around the Arduino Pro Mini, from the AVR/Arduino family.

How big is the Shoe ctrl board?

The Shoe ctrl board measures 82.6 × 76.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Shoe ctrl board?

29 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Shoe ctrl board design files?

From the umass-hrsl/adjustable-compliance-footwear repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Shoe ctrl board design in my own project?

Yes, under the terms of its MIT license, which umass-hrsl chose for the repository.

Can I test firmware for the Shoe ctrl board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in adjustable-compliance-footwear

Similar boards