21 open source boards using the Arduino_Pro_Mini
Real designs built with the Arduino_Pro_Mini, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
EV Charger
fotherja
118 × 103.5 mm53 parts2LMIT166AVR/Arduino
Arduino aprs tracker
billygr
70 × 55 mm21 parts2LNo license75- schematic only · 1 partsAVR/Arduino
Da pimp plus
gutierrezps
1 partsMIT9 AVR/Arduino
MZ-1500 SD
yanataka60
114.8 × 104.4 mm33 parts2LMIT6AVR/Arduino
HB-UNI-TEST-PROG-BOARD V2.2
chianti2000
200.8 × 100.3 mm86 parts2LNo license3AVR/Arduino
H bridge
Miceuz
246.4 × 163.8 mm91 parts2LApache-2.02AVR/Arduino
Battery capacity meter
ikatkov
100 × 99.9 mm68 parts2LNo license1AVR/Arduino
4164-41256-tester
popovb
76.2 × 43.7 mm30 parts2LNo license1AVR/Arduino
F-Stop DarkRoomTimer
c1rk1
121 × 70 mm29 parts2LBSD-3-Clause1AVR/Arduino
Koi mini mp3-player
fajr-lilypad
63.3 × 128.6 mm9 parts2LNo license1AVR/Arduino
Motherboard 2023
RoanTractor
241.5 × 74.6 mm86 parts2LNo license0AVR/Arduino
Satnogs rotator controller
tt-laboratories
100 × 80 mm65 parts2LCERN-OHL-1.20AVR/Arduino
Laser tunnel
aidtopia
75 × 75 mm55 parts2LNo license0AVR/Arduino
Shoe ctrl board
umass-hrsl
82.6 × 76.6 mm29 parts2LMIT0AVR/Arduino
BumWatch
choicebuilds
44 × 44 mm12 parts4LNo license0AVR/Arduino
PicoDeck
tronicbaumi
19.3 × 12.8 mm2 parts2LBSD-3-Clause0AVR/Arduino
Amiga Drawbridge
tebl
90 × 94 mm18 parts2LNo license51AVR/Arduino
Motherboard23-24
RoanTractor
230 × 125 mm78 parts2LNo license0AVR/Arduino
MotorDriver3
aliaafee
50 × 50 mm11 parts2LNo license0AVR/Arduino
Stm32F103Board
danielvilas
104 × 77 mm26 parts2LMIT0AVR/Arduino
BoardArduinos
danielvilas
95 × 53 mm14 parts2LMIT0
How designs wire the Arduino_Pro_Mini
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the Arduino_Pro_Mini connects to, and the resistors, capacitors and other passives placed on it.
- The RESET pins is left unconnected on 72% of them (a signal on 4).
- The D1/TX pin is left unconnected on 7 of 11 designs (a signal on 4).
- The D6 pin has a series resistor on 5 of 12 designs, most often 1 kΩ (then 2.2 kΩ).
- The D7 pin has a series resistor on 5 of 12 designs, most often 1 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| D1/TXpin 1 | Connected to: Not connected 64% · a signal 36% | — |
| RESETpin 3, 27 | Connected to: Not connected 72% · a signal 22% | — |
| D4pin 7 | Connected to: A connector 25% |
|
| D5pin 8 | Connected to: Signal 92% |
|
| D6pin 9 | Connected to: Signal 92% |
|
| D7pin 10 | Connected to: Signal 92% |
|
| D11/MOSIpin 17 | Connected to: Signal 67% · not connected 33% |
|
18 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include EV Charger by fotherja, Arduino aprs tracker by billygr, Amiga Drawbridge by tebl and MZ-1500 SD by yanataka60.
The Arduino_Pro_Mini in open source designs
The gallery holds 21 open source boards using the Arduino_Pro_Mini from 19 GitHub repositories; a typical one measures about 97.5 × 76.8 mm and carries around 29 components.
95% are two-layer designs, the rest use four layers or more, and 48% carry an open source license.
The most starred is EV Charger by fotherja.
Microcontrollers on boards using the Arduino_Pro_Mini
What boards using the Arduino_Pro_Mini are built for
Arduino_Pro_Mini: common questions
Where can I find a Arduino_Pro_Mini reference design?
Each of the 21 boards on this page is a real design using the Arduino_Pro_Mini. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the Arduino_Pro_Mini RESET pin connected?
The RESET pins is left unconnected on 72% of them (a signal on 4). Counted from the KiCad layouts of 17 open source designs using the Arduino_Pro_Mini.
How is the Arduino_Pro_Mini D1/TX pin connected?
The D1/TX pin is left unconnected on 7 of 11 designs (a signal on 4). Counted from the KiCad layouts of 17 open source designs using the Arduino_Pro_Mini.
What resistor goes on the Arduino_Pro_Mini D6 pin?
The D6 pin has a series resistor on 5 of 12 designs, most often 1 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 17 open source designs using the Arduino_Pro_Mini.
What parts are used alongside the Arduino_Pro_Mini?
The LM358, 74LS04 and TP4056 appear in the most repositories here.
Which microcontrollers do boards using the Arduino_Pro_Mini use?
Most are built on AVR/Arduino (21).
How big is a typical board using the Arduino_Pro_Mini?
The median is 97.5 × 76.8 mm, and 95% are two-layer designs.
What is the most popular open source board using the Arduino_Pro_Mini?
By GitHub stars, EV Charger by fotherja, with 166 stars.
Can I simulate one of these boards using the Arduino_Pro_Mini before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.