MicroMouse
USI-27·microMouse·MicroMouse Design Files/mm3.0/mm3.0.kicad_pcb
About the MicroMouse PCB
MicroMouse is an open source RP2040/RP2350 PCB design by USI-27, published on GitHub. It is a 2-layer board measuring 100 × 80 mm, with 55 components from 28 distinct parts.
Its main chip is the C7203003, from the RP2040/RP2350 family. Other key parts include the TB6612FNG, MPU-6050 and AMS1117-5.0. By type, the board carries 18 capacitors, 13 resistors, 8 transistors, 6 diodes, 4 ICs and 2 crystals.
It belongs with the sensors and robotics & motion designs in this gallery.
From the project
A fully autonomous micro mouse built from scratch
This project implements a micromouse robot using a Raspberry Pi Pico W microcontroller. The robot is designed to solve a maze using the flood fill algorithm, with advanced motion control, wall detection, and a custom-designed PCB.
The image above shows the actual hardware implementation of the micromouse robot, featuring:
- Raspberry Pi Pico W at the center - Dual motor setup with encoders - IR sensors for wall detection - Custom PCB design for component integration - Compact and efficient layout
Main components on the MicroMouse
MicroMouse bill of materials (BOM)
55 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C7203003 Pico | RPi_Pico_SMD_TH | U1 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U2 |
| 1 | MPU-6050 | InvenSense_QFN-24_4x4mm_P0.5mm | U3 |
| 1 | AMS1117-5.0 | SOT-223-3_TabPin2 | U4 |
| 4 | TEFT4300 | LED_D3.0mm_Clear | Q1, Q3, Q6, Q7 |
| 4 | DMN1019USN-7 | SOT95P285X140-3N | Q2, Q4, Q5, Q8 |
| 2 | B6B-ZR | B6B-ZR | X1, X2 |
| 1 | B2B | JST_XH_B2B-XH-AM_1x02_P2.50mm_Vertical | J1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | N20 | N20MotorWithMount | N20 |
| 1 | ~ | SW_TL2230EEF140 | S1 |
| 1 | 1N4148WS | D_SOD-323_HandSoldering | D1 |
| 4 | 5MM Emitter | LED_D5.0mm_IRBlack | D2, D3, D4, D5 |
| 1 | C2297 LED_GREEN | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D6 |
| 2 | 10UF 10uF | CP_EIA-3216-10_Kemet-I_Pad1.58x1.35mm_HandSolder | C1, C3 |
| 5 | 100NF 100nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C4, C10, C12, C14 |
| 2 | 10UF 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C8 |
| 2 | 100NF 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6, C7 |
| 3 | 4U7 4u7 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9, C11, C13 |
| 1 | 100N 100n | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C15 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 100N 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16 |
| 1 | 10N 10n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17 |
| 1 | 2N2 2n2 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18 |
| 1 | 1K | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 4 | 2K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2, R3, R4, R5 |
| 2 | C136903 10 ohm | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R12 |
| 4 | 51K 51k | R_2010_5025Metric_Pad1.40x2.65mm_HandSolder | R7, R8, R9, R13 |
| 2 | 5.6OHM 5.6ohm | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10, R11 |
MicroMouse design files
The KiCad project lives in the USI-27/microMouse repository on GitHub; these links point at the commit this page was built from.
MicroMouse: common questions
What microcontroller does the MicroMouse use?
The MicroMouse is built around the C7203003, from the RP2040/RP2350 family.
How big is the MicroMouse PCB?
The MicroMouse measures 100 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MicroMouse?
55 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MicroMouse design files?
From the USI-27/microMouse repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the MicroMouse design in my own project?
The repository has no license, so all rights stay with USI-27. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MicroMouse without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k