MainBMS
uvmaero·CleanSpeed_6.0_Board·BMS1/MainBMS/MainBMS.kicad_pcb
About the MainBMS PCB
MainBMS is an open source ESP32 PCB design by uvmaero, published on GitHub. It is a 2-layer board measuring 94 × 64.8 mm, with 12 components from 9 distinct parts.
Its main chip is the ADG728, from the ESP32 family. By type, the board carries 3 ICs, 3 connectors, 2 diodes, 2 capacitors and 2 resistors.
From the project
PCBs for Clean Speed 6.0
Main components on the MainBMS
MainBMS bill of materials (BOM)
12 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ADG728 ESP32 Dev_Board_C | ESP32-DEV C | U1 |
| 1 | ADG728 TS2940CP33_ROG | VREG_TS2940CP33_ROG | U2 |
| 1 | ADG728 MAX33054EASA+T | SOIC127P600X175-8N | U3 |
| 3 | CONN_01X02 Conn_01x08 | TE_1-776280-1_8pin_Horizontal | J1, J2, J3 |
| 1 | TS4148C RZG | D_0201_0603Metric_Pad0.64x0.40mm_HandSolder | D1 |
| 1 | LED | LED_0201_0603Metric_Pad0.64x0.40mm_HandSolder | D2 |
| 2 | 15U 10uF | C_0201_0603Metric_Pad0.64x0.40mm_HandSolder | C1, C2 |
| 1 | 330 | R_0201_0603Metric_Pad0.64x0.40mm_HandSolder | R1 |
| 1 | 120 | R_0201_0603Metric_Pad0.64x0.40mm_HandSolder | R2 |
MainBMS design files
The KiCad project lives in the uvmaero/CleanSpeed_6.0_Board repository on GitHub; these links point at the commit this page was built from.
MainBMS: common questions
What microcontroller does the MainBMS use?
The MainBMS is built around the ADG728, from the ESP32 family.
How big is the MainBMS PCB?
The MainBMS measures 94 × 64.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MainBMS?
12 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MainBMS design files?
From the uvmaero/CleanSpeed_6.0_Board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the MainBMS design in my own project?
The repository has no license, so all rights stay with uvmaero. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MainBMS without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in CleanSpeed_6.0_Board
On Board
uvmaero
313 × 71.7 mm205 parts2LNo license0ESP32
Big Daddy
uvmaero
245.5 × 127 mm124 parts4LNo license0Bmsstep
uvmaero
313 × 71.7 mm106 parts2LNo license0PAC-man reed
uvmaero
75.5 × 74.2 mm39 parts2LNo license0PACman LV
uvmaero
101.6 × 67.4 mm34 parts2LNo license0- schematic only · 15 parts
Pre:discharge
uvmaero
15 parts2LNo license0
Similar boards
ESP32
Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k