Esp32display
vanceb·esp32display
About the Esp32display PCB
Esp32display is an open source ESP32 PCB design by vanceb, published on GitHub. It is a 4-layer board measuring 36 × 45.6 mm, with 24 components from 19 distinct parts.
Its main chip is the ESP32-WROOM-32D, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 8 resistors, 6 connectors, 4 capacitors, 3 ICs, 2 switches and 1 diode.
From the project
ESP32 project to drive the 64x32 RGB LED Panels (P3, P4, P5)
Main components on the Esp32display
Esp32display bill of materials (BOM)
24 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 LD1117S12TR_SOT223 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-WROOM-32D LIS3DH | LGA-16_3x3mm_P0.5mm_LayoutBorder3x5y | U2 |
| 1 | ESP32-WROOM-32D | ESP32-WROOM-32D | U3 |
| 1 | V_PANEL | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | C165948 USB_C_Receptacle_PowerOnly_6P | USB_C_Receptacle_GCT_USB4125-xx-x_6P_TopMnt_Horizontal | J3 |
| 1 | LIS3DH RGB_PANEL | IDC-Header_2x08_P2.54mm_Vertical | J4 |
| 1 | TOUCH | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J5 |
| 1 | NPX1 | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J6 |
| 1 | NPX1 PROG | PinHeader_1x06_P2.54mm_Vertical | J7 |
| 1 | Reset | SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | C318884 Boot | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | C14996 D_Schottky | D_SMA | D1 |
| 2 | 10U 10u | C_0805_2012Metric | C1, C2 |
| 1 | 100N 100n | C_0603_1608Metric | C4 |
| 1 | 1u | C_0603_1608Metric | C5 |
| 2 | 5K1 5k1 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 3 | 10K 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R5, R6 |
| 1 | LDR07 | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | R4 |
| 2 | 4K7 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8 |
Esp32display design files
The KiCad project lives in the vanceb/esp32display repository on GitHub; these links point at the commit this page was built from.
- Layoutesp32display.kicad_pcb
- Schematicesp32display.kicad_sch
- BOMkikit_fab/bom.csv
Esp32display: common questions
What microcontroller does the Esp32display use?
The Esp32display is built around the ESP32-WROOM-32D, from the ESP32 family.
How big is the Esp32display PCB?
The Esp32display measures 36 × 45.6 mm, has 4 copper layers and is 4.69 mm thick.
How many components are on the Esp32display?
24 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32display design files?
From the vanceb/esp32display repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32display design in my own project?
The repository has no license, so all rights stay with vanceb. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32display without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k