4Bit Adder
Ventratrat·KiCad-proj·4-Bit Adder/4Bit_Adder.kicad_pcb
About the 4Bit Adder PCB
4Bit Adder is an open source AVR/Arduino PCB design by Ventratrat, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 78.7 × 71.1 mm, with 25 components from 8 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the 74LS257, SN74HC74N and 74LS283. By type, the board carries 10 switches, 5 diodes, 5 resistors, 4 ICs and 1 module.
From the project
KiCAD schematics and layouts I worked on
Main components on the 4Bit Adder
4Bit Adder bill of materials (BOM)
25 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 74LS257 | SOIC-16_W7.5mm | U1 |
| 2 | SN74HC74N Texas Instruments | DIP-14_W3mm | U2, U7 |
| 1 | 74LS283 | DIP-16_W10.16mm | U6 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | EG1218 E-Switch | PushButton_12x12mm_THT_GPTS203211B | S1 |
| 9 | EG1218 E-Switch | Switch_Slide_11.6x4mm_EG1218 | S2, S3, S4, S5, S6, S7, S8, S9 +1 |
| 5 | LED | LED_5mm_Radial | D1, D2, D3, D4, D5 |
| 5 | 330 | R_1watt | R1, R2, R3, R4, R5 |
4Bit Adder design files
The KiCad project lives in the Ventratrat/KiCad-proj repository on GitHub; these links point at the commit this page was built from.
4Bit Adder: common questions
What microcontroller does the 4Bit Adder use?
The 4Bit Adder is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the 4Bit Adder PCB?
The 4Bit Adder measures 78.7 × 71.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the 4Bit Adder?
25 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the 4Bit Adder design files?
From the Ventratrat/KiCad-proj repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the 4Bit Adder design in my own project?
Yes, under the terms of its GPL-3.0 license, which Ventratrat chose for the repository.
Can I test firmware for the 4Bit Adder without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in KiCad-proj
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k