Firmware agent
VibeBB·firmware-agent·examples/desk-lamp-s3/circuit/desk-lamp.net
About the Firmware agent PCB
Firmware agent is an open source ESP32 PCB design by VibeBB, published on GitHub under the BSD-3-Clause license. It is a board, with 8 components from 8 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. By type, the board carries 3 connectors, 1 IC, 1 transistor, 1 switch, 1 capacitor and 1 resistor.
It belongs with the sensors designs in this gallery.
From the project
Design a real hardware product with AI — this is the firmware sister of the VibeBB plugin family for AgentCanvas / OpenHands (https://vibebb.org/).
Design a real hardware product with AI — this is the firmware sister of the VibeBB plugin family for AgentCanvas / OpenHands (https://vibebb.org/).
It decides which pin on the chip does what (LEDs, sensors, buzzers, USB), checks that your firmware builds, fits in the chip's memory, and behaves correctly inside a simulator — and that the chosen pins actually match the circuit board the circuit plugin designed.
Main components on the Firmware agent
Firmware agent bill of materials (BOM)
8 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8 | ESP32-S3-WROOM-1 | U1 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | DEBUG | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | LED | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 1 | 5V_IN | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J3 |
| 1 | MODE | SW_SPST_PTS645 | SW1 |
| 1 | 1u | C_0402_1005Metric | C1 |
| 1 | 10k | R_0402_1005Metric | R1 |
Firmware agent design files
The KiCad project lives in the VibeBB/firmware-agent repository on GitHub; these links point at the commit this page was built from.
Firmware agent: common questions
What microcontroller does the Firmware agent use?
The Firmware agent is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How many components are on the Firmware agent?
8 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Firmware agent design files?
From the VibeBB/firmware-agent repository on GitHub, which has a netlist; the links under Design files point to each one.
Can I use the Firmware agent design in my own project?
Yes, under the terms of its BSD-3-Clause license, which VibeBB chose for the repository.
Can I test firmware for the Firmware agent without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k