Iplanter
vineethjkatti-tech·iplanter·KICAD/iplanter.kicad_pcb
About the Iplanter PCB
Iplanter is an open source ESP8266 PCB design by vineethjkatti-tech, published on GitHub. It is a 2-layer board measuring 52.3 × 52.7 mm, with 5 components from 5 distinct parts.
Its main chip is the WEMOS_D1_mini, from the ESP8266 family. By type, the board carries 4 connectors and 1 IC.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
iplanter is a smart planter which uses moisture and temperature sensor to display the health of the plant on an OLED display.
Main components on the Iplanter
Iplanter bill of materials (BOM)
5 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | WEMOS_D1_mini | WEMOS_D1_mini_light | U2 |
| 1 | Moisture Sensor | PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Right | J1 |
| 1 | Display | PinHeader_1x04_P2.54mm_Vertical_SMD_Pin1Right | J2 |
| 1 | DHT11 | PinSocket_1x03_P2.54mm_Vertical | J3 |
| 1 | Barrel_Jack_MountingPin | BarrelJack_Horizontal | J4 |
Iplanter design files
The KiCad project lives in the vineethjkatti-tech/iplanter repository on GitHub; these links point at the commit this page was built from.
- LayoutKICAD/iplanter.kicad_pcb
- SchematicKICAD/iplanter.kicad_sch
- BOMDocs/BOM.csv
Iplanter: common questions
What microcontroller does the Iplanter use?
The Iplanter is built around the WEMOS_D1_mini, from the ESP8266 family.
How big is the Iplanter PCB?
The Iplanter measures 52.3 × 52.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Iplanter?
5 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Iplanter design files?
From the vineethjkatti-tech/iplanter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Iplanter design in my own project?
The repository has no license, so all rights stay with vineethjkatti-tech. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Iplanter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
Similar boards
ESP8266
ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1kESP8266
HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738ESP8266
RatGDO-OpenSource-Bare-ESP8266
Kaldek
55 × 82.7 mm20 parts2LMIT506ESP8266
Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506ESP8266
RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506ESP8266
Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398