MAIN WATERING
Vlebi·smart-watering·.MAIN_PCB/MAIN_WATERING/MAIN_WATERING.kicad_pcb
About the MAIN WATERING PCB
MAIN WATERING is an open source ESP32 PCB design by Vlebi, published on GitHub under the MIT license. It is a 2-layer board measuring 35.5 × 37 mm, with 5 components from 5 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 1 IC, 1 connector, 1 switch, 1 diode and 1 resistor.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
A smart watering sytem built whit a master circuit and a node for every waterable plant.
A node based smart watering system using MAC addres based wireless communication between a main module and separate node modules with theoritically no limit for how many nodes it can use.
- System Architecture - Bill of Materials - Hardware Design (KiCad) - Software Stack & Firmware - Project Journal & Media - Getting Started
DripLogic uses two or more hardware units that communicate without a router, using ESP-NOW.
Main components on the MAIN WATERING
MAIN WATERING bill of materials (BOM)
5 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | ESP32-C3-SuperMini | U1 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | LED | LED_D5.0mm | D1 |
| 1 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
MAIN WATERING design files
The KiCad project lives in the Vlebi/smart-watering repository on GitHub; these links point at the commit this page was built from.
MAIN WATERING: common questions
What microcontroller does the MAIN WATERING use?
The MAIN WATERING is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the MAIN WATERING PCB?
The MAIN WATERING measures 35.5 × 37 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MAIN WATERING?
5 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the MAIN WATERING design files?
From the Vlebi/smart-watering repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the MAIN WATERING design in my own project?
Yes, under the terms of its MIT license, which Vlebi chose for the repository.
Can I test firmware for the MAIN WATERING without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in smart-watering
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k