Synthesizer-VHF

wa1hco·Synthesizer-VHF·hardware/Synthesizer-VHF.kicad_pcb

Synthesizer-VHF PCB layout, top view — open source AVR/Arduino board by wa1hco

About the Synthesizer-VHF PCB

Synthesizer-VHF is an open source AVR/Arduino PCB design by wa1hco, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 39 × 37.7 mm, with 83 components from 42 distinct parts.

Its main chip is the ATtiny1616-M, from the AVR/Arduino family. Other key parts include the LM7805A, FT231XQ, ADF4351 and ADP150AUJZ-3.3-R7. By type, the board carries 36 capacitors, 23 resistors, 8 connectors, 8 diodes, 6 ICs and 1 crystal.

It belongs with the audio and rf & radio designs in this gallery.

From the project

35 MHz–4.4 GHz ADF4351 synthesizer: ATtiny1616 + USB-C, 10 MHz ref in/out, JLCPCB-ready KiCad board for a Hammond die-cast box

VHF synthesizer board built around an Analog Devices ADF4351 PLL, an ATtiny1616, a TCXO reference, USB serial, and a 12 V input with onboard regulators. The board has two RF outputs. SPI between the ATtiny1616 and the PLL is wired to general-purpose pins, and the firmware bit-bangs it.

- hardware/ — KiCad project (Synthesizer-VHF.kicadpro), design rules, the phase-noise spreadsheet, and fabrication-toolkit options. - hardware/libraries/ — project symbol and footprint libraries. See Libraries below. - hardware/datasheets/ — component datasheets. - hardware/jlcpcb/ — fab outputs committed with…

Main components on the Synthesizer-VHF

Synthesizer-VHF bill of materials (BOM)

83 components, 42 distinct parts.

QtyPartRefs
1
LM7805A
U1
1
FT231XQ
U2
1
ATtiny1616-M
U3
1
ADF4351
U4
2
ADP150AUJZ-3.3-R7
U7, U8
1
HCI 8122S-25NQ33FTL
X1
1
Screw_Terminal_01x02
J1
2
Scope
J2, J6
1
USB-C 2.0 16P
J4
1
REF_IN
J5
1
RFOUTA
J7
1
Header 1x3
J8
1
RFOUTB
J9
1
D_Schottky
D1
2
MM3Z3V6
D2, D6
1
blue
D3
2
Yellow
D4, D5
1
PA2
D7
1
PA3
D8
1
FerriteBead_Small
FB1
Show 22 more
QtyPartRefs
1
330n 50V
C1
13
100n
C2, C6, C7, C13, C15, C16, C18, C22 +5
3
10n
C3, C4, C5
1
6.8u
C8
2
47p
C9, C11
7
10p
C10, C19, C21, C24, C26, C28, C37
2
100p
C12, C23
3
1u 10V
C14, C27, C33
1
4.7n
C17
1
2.7n
C20
1
680p
C31
1
1u 10V
C32
2
5K1
R1, R3
2
0R
R2, R20
5
49R9
R5, R11, R15, R21, R23
1
330R
R6
1
15R
R7
7
1K
R8, R9, R10, R12, R16, R17, R19
2
22R
R13, R24
1
560R
R14
1
4K7
R22
1
1K
R25

Synthesizer-VHF design files

The KiCad project lives in the wa1hco/Synthesizer-VHF repository on GitHub; these links point at the commit this page was built from.

Synthesizer-VHF: common questions

What microcontroller does the Synthesizer-VHF use?

The Synthesizer-VHF is built around the ATtiny1616-M, from the AVR/Arduino family.

How big is the Synthesizer-VHF PCB?

The Synthesizer-VHF measures 39 × 37.7 mm, has 4 copper layers and is 1.6472 mm thick.

How many components are on the Synthesizer-VHF?

83 components, from 42 distinct parts. The full bill of materials is listed on this page.

Where can I download the Synthesizer-VHF design files?

From the wa1hco/Synthesizer-VHF repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Synthesizer-VHF design in my own project?

Yes, under the terms of its GPL-3.0 license, which wa1hco chose for the repository.

Can I test firmware for the Synthesizer-VHF without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards