Drone
wanbings·drone-pcb
About the Drone PCB
Drone is an open source RP2040/RP2350 PCB design by wanbings, published on GitHub. It is a 4-layer board measuring 52.5 × 52.5 mm, with 47 components from 29 distinct parts.
Its main chip is the RaspberryPi_Pico, from the RP2040/RP2350 family. Other key parts include the TLV61070ADBV, AP2112K-3.3 and MPU-6050. By type, the board carries 10 connectors, 8 capacitors, 6 resistors, 4 transistors, 4 diodes and 3 ICs.
It belongs with the robotics & motion designs in this gallery.
From the project
kicad hardware design files and schematics for a custom 4-layer rp2350-based flight controller pcb
Main components on the Drone
Drone bill of materials (BOM)
47 components, 29 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TLV61070ADBV | SOT-23-6 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | MPU-6050 | InvenSense_QFN-24_4x4mm_P0.5mm | U3 |
| 1 | RaspberryPi_Pico | RaspberryPi_Pico_Common_Unspecified | A1 |
| 4 | AO3400A | SOT-23 | Q1, Q2, Q3, Q4 |
| 1 | HappyModel EP1 | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | BATT | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | M1_NEG | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J3 |
| 1 | M1_POS | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J4 |
| 1 | M2_POS | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J5 |
| 1 | M2_NEG | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J6 |
| 1 | M3_POS | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J7 |
| 1 | M3_NEG | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J8 |
| 1 | M4_POS | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J9 |
| 1 | M4_NEG | SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mm | J10 |
| 2 | 4.7uF | C_0805_2012Metric | C_3, C_4 |
| 4 | 100 Ω | R_0805_2012Metric | GATE1, GATE2, GATE3, GATE4 |
| 4 | 10 kΩ | R_0805_2012Metric | PULLDOWN1, PULLDOWN2, PULLDOWN3, PULLDOWN4 |
| 4 | SS24 | D_SMA | D1, D2, D3, D4 |
| 1 | 2.2uH | L_1008_2520Metric | L1 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 100nF | C_0805_2012Metric | C1 |
| 2 | 100µF | C_1206_3216Metric | C2, C8 |
| 1 | 2.2nF | C_0805_2012Metric | C3 |
| 3 | 0.1uF | C_0805_2012Metric | C4, C5, C6 |
| 1 | 22uF | C_0805_2012Metric | C7 |
| 2 | 10kΩ | R_0805_2012Metric | R1, R2 |
| 2 | 4.7kΩ | R_0805_2012Metric | R3, R4 |
| 1 | 910kΩ | R_0805_2012Metric | R6 |
| 1 | 100kΩ | R_0805_2012Metric | R7 |
Drone design files
The KiCad project lives in the wanbings/drone-pcb repository on GitHub; these links point at the commit this page was built from.
- Layoutdrone_pcb.kicad_pcb
- Schematicdrone_pcb.kicad_sch
Drone: common questions
What microcontroller does the Drone use?
The Drone is built around the RaspberryPi_Pico, from the RP2040/RP2350 family.
How big is the Drone PCB?
The Drone measures 52.5 × 52.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Drone?
47 components, from 29 distinct parts. The full bill of materials is listed on this page.
Where can I download the Drone design files?
From the wanbings/drone-pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Drone design in my own project?
The repository has no license, so all rights stay with wanbings. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Drone without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k