CO2-Monitor
wkcollis1-eng·CO2-Monitor·hardware/CO2 Monitor.kicad_pcb
About the CO2-Monitor PCB
CO2-Monitor is an open source ESP32 PCB design by wkcollis1-eng, published on GitHub under the CC-BY-4.0 license. It is a 2-layer board measuring 23 × 38 mm, with 4 components from 4 distinct parts.
Its main chip is the Xiao ESP32C3, from the ESP32 family. By type, the board carries 1 IC, 1 capacitor and 1 resistor.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
Adafruit SCD30 NDIR CO2 sensor on a XIAO ESP32-C3, reporting to Home Assistant. ESPHome firmware with a stale-sensor watchdog, its host-side fault-injection harness, and a KiCad enclosure fit-check model.
NDIR CO2 Sensing for Two Rooms, Built to Fail Visibly
Two CO2 nodes, one in a bedroom and one in a family room. Each pairs an Adafruit SCD30 (PID 4867, a Sensirion NDIR sensor) with a Seeed XIAO ESP32-C3 on a small carrier board, inside a Hammond 1551V4 enclosure. They run ESPHome and report to Home Assistant.
All behaviour lives in one file, esphome/co2-node-common.yaml. Each node file holds nothing but its name and its own API key.
Main components on the CO2-Monitor
CO2-Monitor bill of materials (BOM)
4 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Xiao ESP32C3 | XIAO ESP32C3 | U1 |
| 1 | PinHeader_1x04_P2.54mm_Horizontal | PinHeader_1x04_P2.54mm_Horizontal | PH1 |
| 1 | .1uF 50V | C_Disc_D5.0mm_W2.5mm_P2.50mm | C1 |
| 1 | 1K Ohm | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
CO2-Monitor design files
The KiCad project lives in the wkcollis1-eng/CO2-Monitor repository on GitHub; these links point at the commit this page was built from.
CO2-Monitor: common questions
What microcontroller does the CO2-Monitor use?
The CO2-Monitor is built around the Xiao ESP32C3, from the ESP32 family.
How big is the CO2-Monitor PCB?
The CO2-Monitor measures 23 × 38 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CO2-Monitor?
4 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the CO2-Monitor design files?
From the wkcollis1-eng/CO2-Monitor repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the CO2-Monitor design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which wkcollis1-eng chose for the repository.
Can I test firmware for the CO2-Monitor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k