Stepper blinds driver
xavier-phillips·stepper-blinds-driver·hardware/pcb/kicad/kicad.kicad_pcb
About the Stepper blinds driver PCB
Stepper blinds driver is an open source ESP32 PCB design by xavier-phillips, published on GitHub under the MIT license. It is a 2-layer board measuring 48 × 46.6 mm, with 6 components from 6 distinct parts.
Its main chip is the ESP32-C6-Super-Mini-Header, from the ESP32 family. By type, the board carries 1 module, 1 connector and 1 capacitor.
It belongs with the robotics & motion, retro computing and iot & wireless designs in this gallery.
From the project
An ultra-quiet NEMA 17 retrofit driver for beaded-chain roller blinds.
A NEMA 17 retrofit driver for beaded-chain roller blinds, designed to run under 40dB (noise not yet measured).
Commercial options have some limitations: - Can be very expensive - Almost all commercial devices use geared DC motors, and are very loud when in operation (>50dB)
What impacts motor noise? - DC Brushed Motors - Brush scratching - Geared Motors - Vibrations and friction - Magnetic hum & coil whine

Stepper blinds driver bill of materials (BOM)
6 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Stepper_Motor_bipolar | TerminalBlock_Phoenix_MKDS-1,5-4-5.08_1x04_P5.08mm_Horizontal | M1 |
| 1 | Barrel_Jack | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | ~ | ESP32-C6-Super-Mini-Header | ESP32-C6-Super-Mini1 |
| 1 | ~ | MP1584EN-Module | MP1584EN1 |
| 1 | ~ | TMC2209-Module | TMC2209 |
| 1 | 100µF | C_Radial_D10.0mm_H20.0mm_P5.00mm | C1 |
Stepper blinds driver design files
The KiCad project lives in the xavier-phillips/stepper-blinds-driver repository on GitHub; these links point at the commit this page was built from.
Stepper blinds driver: common questions
What microcontroller does the Stepper blinds driver use?
The Stepper blinds driver is built around the ESP32-C6-Super-Mini-Header, from the ESP32 family.
How big is the Stepper blinds driver PCB?
The Stepper blinds driver measures 48 × 46.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stepper blinds driver?
6 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stepper blinds driver design files?
From the xavier-phillips/stepper-blinds-driver repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Stepper blinds driver design in my own project?
Yes, under the terms of its MIT license, which xavier-phillips chose for the repository.
Can I test firmware for the Stepper blinds driver without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k