OpenWheel
xlazam01·OpenWheel·hw/filter_wheel.kicad_pcb
About the OpenWheel PCB
OpenWheel is an open source STM32 PCB design by xlazam01, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 26.9 × 35.3 mm, with 57 components from 29 distinct parts.
Its main chip is the STM32G0B1CBTX, from the STM32 family. Other key parts include the USBLC6-2SC6, RT9193-33, 24AA64T-I/OT and TMC2209-LA. By type, the board carries 24 capacitors, 19 resistors, 5 ICs, 3 connectors, 2 switches and 2 diodes.
It belongs with the robotics & motion, sensors and science & space designs in this gallery.
From the project
Open-source motorised filter wheel for astrophotography - 4 x 2" DIY build, STM32 + TMC2209, hall-sensor slot detection, ASCOM and INDI drivers
Open-source motorised filter wheel for astrophotography (up to 9 filters; the DIY release takes 4 × 2"). It appears on the PC as a USB serial device, is detected automatically, and is driven from NINA and other ASCOM clients, or from KStars/Ekos through INDI.
- Hold the CCW button while powering on. The CCW button is wired to the BOOT0 pin, so the STM32 starts its built-in USB DFU bootloader instead of the firmware. - On a running wheel the command :31# does the same without touching the button (flag in RAM + reset, see docs/BOOTLOADER.md).

Main components on the OpenWheel
OpenWheel bill of materials (BOM)
57 components, 29 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | RT9193-33 ME6231A33M3G | SOT-23 | U2 |
| 1 | STM32G0B1CBTX STM32G0B1CBTx | LQFP-48_7x7mm_P0.5mm | U3 |
| 1 | 24AA64T-I/OT | SOT-23-5 | U4 |
| 1 | TMC2209-LA | QFN-28-1EP_5x5mm_P0.5mm_EP3.75x3.75mm_ThermalVias | U5 |
| 1 | C400090 TAXM8M4RDBCCT2T / 8MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | MC-311D | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 1 | JST B4B-PH-K Motor | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J3 |
| 1 | JST B3B-PH-K Hall | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J4 |
| 1 | SMD0603P050TF | Fuse_0603_1608Metric | F1 |
| 1 | TS-1088-AR02016 CCW / BOOT0 | SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 1 | TS-1088-AR02016 CW | SW_Push_SPST_NO_Alps_SKRK | SW3 |
| 2 | C2286 RED | LED_0603_1608Metric | D1, D2 |
| 1 | 4.7NF 4.7nF | C_0402_1005Metric | C1 |
| 3 | 1UF 1uF | C_0402_1005Metric | C2, C3, C10 |
| 7 | 100NF 100nF | C_0402_1005Metric | C4, C7, C8, C9, C13, C23, C25 |
| 4 | 10UF/10V 10uF/10V | C_0402_1005Metric | C6, C16, C17, C21 |
| 2 | 12PF 12pF | C_0402_1005Metric | C11, C12 |
| 4 | 100NF/50V 100nF | C_0402_1005Metric | C14, C15, C20, C22 |
| 1 | 47UF/10V 47uF/10V | C_1206_3216Metric | C18 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 22NF/50V 22nF/50V | C_0402_1005Metric | C19 |
| 1 | 1NF 1nF | C_0402_1005Metric | C24 |
| 6 | 5K1 5k1 | R_0402_1005Metric | R1, R2, R10, R11, R12, R13 |
| 1 | 1M | R_0402_1005Metric | R3 |
| 7 | 10K 10k | R_0402_1005Metric | R4, R7, R9, R14, R18, R20, R21 |
| 1 | 510R | R_0402_1005Metric | R8 |
| 1 | 1K5 1k5 | R_0402_1005Metric | R15 |
| 2 | 0.11R | R_0805_2012Metric | R16, R17 |
| 1 | 100R | R_0402_1005Metric | R19 |
OpenWheel design files
The KiCad project lives in the xlazam01/OpenWheel repository on GitHub; these links point at the commit this page was built from.
OpenWheel: common questions
What microcontroller does the OpenWheel use?
The OpenWheel is built around the STM32G0B1CBTX, from the STM32 family.
How big is the OpenWheel PCB?
The OpenWheel measures 26.9 × 35.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the OpenWheel?
57 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the OpenWheel design files?
From the xlazam01/OpenWheel repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the OpenWheel design in my own project?
Yes, under the terms of its GPL-3.0 license, which xlazam01 chose for the repository.
Can I test firmware for the OpenWheel without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k