Hw module gps
xtech·hw-module-gps
About the Hw module gps
Hw module gps is an open source AVR/Arduino PCB design by xtech, published on GitHub under the CC-BY-4.0 license. It is a 4-layer board measuring 93.3 × 58 mm, with 14 components from 12 distinct parts.
Its main chip is the Ardusimple_F9P, from the AVR/Arduino family. Other key parts include the AMS1117-3.3, 2.54mm 1x6 socket, 2.54mm 1x8 socket and 2.54mm 1x10 socket. By type, the board carries 5 ICs, 4 capacitors, 2 resistors, 1 connector and 1 diode.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
Module for using Arduino Shield style GPS units with xBot modular platform
A KiCad PCB design for a GPS module intended for the OpenMower universal mainboard. Part of the OpenMower project — open-source RTK GPS lawn mowing robotics.
All production files are pre-generated in release/:
1. Upload release/hw-module-gps-JLCPCB.zip as gerbers 2. Enable PCB Assembly, upload: - release/hw-module-gpsbomjlc.csv as BOM - release/hw-module-gpscpljlc.csv as CPL 3. Use release/hw-module-gps-ibom.html (open in browser) to verify component placement

Main components on the Hw module gps
Hw module gps bill of materials (BOM)
14 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U12 |
| 1 | 2.54mm 1x6 socket | Dummy | U42 |
| 2 | 2.54mm 1x8 socket | Dummy | U43, U44 |
| 1 | 2.54mm 1x10 socket | Dummy | U45 |
| 1 | Conn_01x05 | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J29 |
| 1 | Ardusimple_F9P | Arduino_Uno_Shield_Ardusimple_Budget | XA1 |
| 1 | LED GREEN | LED_0805_2012Metric | D25 |
| 1 | 10uF | C_0402_1005Metric | C37 |
| 1 | 100nF | C_0402_1005Metric | C63 |
| 2 | 22uF | C_0603_1608Metric | C119, C120 |
| 1 | 1k | R_0805_2012Metric | R44 |
| 1 | 2.2k | R_0805_2012Metric | R59 |
Hw module gps design files
The KiCad project lives in the xtech/hw-module-gps repository on GitHub; these links point at the commit this page was built from.
- Layouthw-module-gps.kicad_pcb
- Schematichw-module-gps.kicad_sch
Hw module gps: common questions
What microcontroller does the Hw module gps use?
The Hw module gps is built around the Ardusimple_F9P, from the AVR/Arduino family.
How big is the Hw module gps?
The Hw module gps measures 93.3 × 58 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Hw module gps?
14 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Hw module gps design files?
From the xtech/hw-module-gps repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Hw module gps design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which xtech chose for the repository.
Can I test firmware for the Hw module gps without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k