EnvDaqBox

Yongci·EnvDaqBox-PCB

EnvDaqBox PCB layout, top view — open source ESP32 board by Yongci

About the EnvDaqBox PCB

EnvDaqBox is an open source ESP32 PCB design by Yongci, published on GitHub under the Apache-2.0 license. It is a 4-layer board measuring 96.3 × 71 mm, with 96 components from 49 distinct parts.

Its main chip is the ESP32-C6-MINI-1U, from the ESP32 family. Other key parts include the CH224Q, CH9442Q, SGM2212-3.3XOB2G/TR, TPS56A37RPAR and TSU111HYLT. By type, the board carries 33 capacitors, 33 resistors, 7 ICs, 6 connectors, 5 diodes and 4 fuses.

It belongs with the iot & wireless designs in this gallery.

From the project

This is a development board designed for automated flower watering or smart agriculture, primarily used for controlling the watering and lighting systems. It is currently under development. The development board utilizes Espressif Systems' ESP32-C6 as the main controller. This So

This is a development board designed for automated flower watering or smart agriculture, primarily used for controlling the watering and lighting systems. It is currently under development. The development board utilizes Espressif Systems' ESP32-C6 as the main controller. This SoC is based on the RISC-V architecture core and supports ultra-low power consumption and WiFi-6 (802.11ax).

EnvDaqBox, from the project README
From the project README

Main components on the EnvDaqBox

CH224QCH9442QSGM2212-3.3XOB2G/TRTPS56A37RPARTSU111HYLTESP32-C6-MINI-1USGM2212-5.0XOB2G/TR

EnvDaqBox bill of materials (BOM)

96 components, 49 distinct parts.

QtyPartRefs
1
CH224Q
U1
1
CH9442Q
U2
1
SGM2212-3.3XOB2G/TR
U3
1
TPS56A37RPAR
U4
1
TSU111HYLT
U5
1
ESP32-C6-MINI-1U
U6
1
SGM2212-5.0XOB2G/TR
U7
2
S8050
Q1, Q2
1
32kHz
Y1
1
Screw_Terminal_01x04
J1
1
Conn_01x02_Pin
J2
1
Conn_01x05_Pin
J3
2
Conn_01x04_Pin
J4, J5
1
TYPE-C-Receptacle-2.0
P1
2
SW_Push
Boot_key1, Reset1
1
5A/33V
F1
1
15A
F2
2
5A/16V
F4, F5
2
JQC-3FF-005-1H
K1, K2
1
BZT52C3V3
D2
Show 29 more
QtyPartRefs
2
1N4007
D3, D4
1
WS2812B
D5
1
1N4148W
D6
1
5.6uH
L1
2
1uF/50V(10%)
C1, C19
11
0.1uF/50V(10%)
C2, C15, C16, C18, C20, C22, C23, C24 +3
2
10uF/50V(20%)
C3, C4
2
0.1uF/50V(10%)
C5, C7
1
47nF/50V(10%)
C6
1
47pF/50V(10%)
C8
5
22uF/25V(10%)
C9, C10, C11, C12, C13
5
10uF/25V(20%)
C14, C17, C25, C30, C33
1
0.1uF/6V(10%)
C21
1
1uF
C26
2
12pF
C28, C29
1
56k(1%)
R1
12
0
R2, R3, R4, R6, R9, R11, R13, R22 +4
5
10k
R5, R8, R21, R28, R32
1
52.3k(1%)
R7
1
20k(1%)
R10
1
400k(1%)
R12
1
120k(1%)
R14
1
43k(1%)
R15
3
1k(1%)
R16, R17, R19
2
5.1k(1%)
R18, R20
2
0(1%)
R23, R24
1
3.3k(1%)
R25
1
10k(1%)
R26
1
0(1%)
R27

EnvDaqBox design files

The KiCad project lives in the Yongci/EnvDaqBox-PCB repository on GitHub; these links point at the commit this page was built from.

EnvDaqBox: common questions

What microcontroller does the EnvDaqBox use?

The EnvDaqBox is built around the ESP32-C6-MINI-1U, from the ESP32 family.

How big is the EnvDaqBox PCB?

The EnvDaqBox measures 96.3 × 71 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the EnvDaqBox?

96 components, from 49 distinct parts. The full bill of materials is listed on this page.

Where can I download the EnvDaqBox design files?

From the Yongci/EnvDaqBox-PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the EnvDaqBox design in my own project?

Yes, under the terms of its Apache-2.0 license, which Yongci chose for the repository.

Can I test firmware for the EnvDaqBox without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards