Jarvis clock
yuralakatosh25-maker·jarvis-clock·PCB/jarvis-clock.kicad_pcb
About the Jarvis clock PCB
Jarvis clock is an open source ESP32 PCB design by yuralakatosh25-maker, published on GitHub. It is a 2-layer board measuring 90 × 56 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 4 connectors, 2 switches and 1 IC.
It belongs with the audio, keyboards and iot & wireless designs in this gallery.
From the project
Cyberpunk desk alarm clock with a Gemini-powered voice assistant ("Hey Jarvis"), anime face on a 2.25" ST7789 screen, neon light grooves and a custom KiCad PCB. XIAO ESP32C3 + Hack Club BLARE.
A desk alarm clock with a voice assistant (say "Hey Jarvis"), a pixel-art anime face on a tiny 2.25" screen, a cyberpunk wedge case with neon light grooves, and a custom PCB. Built for Hack Club BLARE.
From bottom to top: tray (PCB stands on 4 heat-set standoffs, speaker sits on the floor over a hex grille, rubber feet) -> PCB -> shell (screen pocket in the 60 degree slope, key openings, neon grooves, hex vents, USB-C opening) -> neon covers and keycaps. The shell is held to the tray by 4 M3x16 screws from below (into heat-set inserts in the shell posts); the PCB is held by 4 M3x8 screws.

Main components on the Jarvis clock
Jarvis clock bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Conn_01x07_Pin | PinHeader_1x07_P2.54mm_Vertical | J3 |
| 1 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
Jarvis clock design files
The KiCad project lives in the yuralakatosh25-maker/jarvis-clock repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/jarvis-clock.kicad_pcb
- SchematicPCB/jarvis-clock.kicad_sch
Jarvis clock: common questions
What microcontroller does the Jarvis clock use?
The Jarvis clock is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Jarvis clock PCB?
The Jarvis clock measures 90 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Jarvis clock?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Jarvis clock design files?
From the yuralakatosh25-maker/jarvis-clock repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Jarvis clock design in my own project?
The repository has no license, so all rights stay with yuralakatosh25-maker. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Jarvis clock without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k