Lab3
yuwennnnnnnnnnnn·514·Lab3/Lab3/Lab3.kicad_pcb
About the Lab3 PCB
Lab3 is an open source ESP32 PCB design by yuwennnnnnnnnnnn, published on GitHub. It is a 2-layer board measuring 23.4 × 13.7 mm, with 13 components from 10 distinct parts.
Its main chip is the ESP32C3, from the ESP32 family. Other key parts include the ULN2003A. By type, the board carries 5 resistors, 4 capacitors, 2 ICs, 1 connector and 1 diode.
Main components on the Lab3
Lab3 bill of materials (BOM)
13 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32C3 ADP3331ARTZ-REEL7 | RJ_6_ADI | U1 |
| 1 | ULN2003A LSM6DSOXTR | LGA-14L_STM | U2 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P1.00mm_Vertical | J1 |
| 1 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 2 | 0.47µF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 2 | 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4 |
| 1 | R | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 634 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 365 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 2 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5 |
Lab3 design files
The KiCad project lives in the yuwennnnnnnnnnnn/514 repository on GitHub; these links point at the commit this page was built from.
- LayoutLab3/Lab3/Lab3.kicad_pcb
- SchematicLab3/Lab3/Lab3.kicad_sch
- BOMFinalProject/ BOM.csv
Lab3: common questions
What microcontroller does the Lab3 use?
The Lab3 is built around the ESP32C3, from the ESP32 family.
How big is the Lab3 PCB?
The Lab3 measures 23.4 × 13.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Lab3?
13 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Lab3 design files?
From the yuwennnnnnnnnnnn/514 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Lab3 design in my own project?
The repository has no license, so all rights stay with yuwennnnnnnnnnnn. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Lab3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in 514
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k