Troxler gauge interface
zhuffman93·troxler-gauge-interface·hardware/troxler-interface-pcb.kicad_pcb
About the Troxler gauge interface PCB
Troxler gauge interface is an open source Raspberry Pi PCB design by zhuffman93, published on GitHub. It is a 2-layer board measuring 52.5 × 55.5 mm, with 9 components from 5 distinct parts.
Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. Other key parts include the MAX3232. By type, the board carries 5 capacitors, 2 connectors, 1 IC and 1 module.
From the project
Pico W based interface for Troxler gauges
KiCad 10 project for the interface board.
- 52.5 x 55.5 mm, 2 copper layers, 1.6 mm thick - Raspberry Pi Pico W soldered on its castellated edge pads. The USB port overhangs the right edge by 1.35 mm. The antenna sits at the left edge inside a copper keepout. - MAX3232 (SOIC-16) and five 0603 capacitors mount on the bottom face. - Winford CNR25M (DB25 male, gauge side) and CNR9F (DB9 female, printer side). Both are right-angle parts with plated board-lock holes. Solder the locks for strength. - Four M3 mounting holes (H1 to H4). The enclosure screws pass through these holes. - The board gets…
Main components on the Troxler gauge interface
Troxler gauge interface bill of materials (BOM)
9 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MAX3232 | SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | RaspberryPi_Pico_W | RaspberryPi_Pico_W_SMD_HandSolder | A1 |
| 1 | DB25_Pins | DSUB-25_Pins_Horizontal_P2.77x2.84mm_EdgePinOffset9.40mm | J1 |
| 1 | DE9_Socket | DSUB-9_Socket_Horizontal_P2.77x2.84mm_EdgePinOffset9.40mm | J2 |
| 5 | 100nF | C_0603_1608Metric | C1, C2, C3, C4, C5 |
Troxler gauge interface design files
The KiCad project lives in the zhuffman93/troxler-gauge-interface repository on GitHub; these links point at the commit this page was built from.
Troxler gauge interface: common questions
What microcontroller does the Troxler gauge interface use?
The Troxler gauge interface is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.
How big is the Troxler gauge interface PCB?
The Troxler gauge interface measures 52.5 × 55.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Troxler gauge interface?
9 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the Troxler gauge interface design files?
From the zhuffman93/troxler-gauge-interface repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Troxler gauge interface design in my own project?
The repository has no license, so all rights stay with zhuffman93. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Troxler gauge interface without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507