LED HEART
zukunho·LED_HEART·hardware/kicad/LEDS_VALETN.kicad_pcb
About the LED HEART PCB
LED HEART is an open source ESP32 PCB design by zukunho, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 114.9 × 105.1 mm, with 30 components from 3 distinct parts.
Its main chip is the ESP32-WROOM, from the ESP32 family. By type, the board carries 28 diodes, 1 IC and 1 switch.
From the project
A heart-shaped PCB with 28 LEDs controlled by an ESP32 using Charlieplexing, designed in KiCad.
A heart-shaped PCB with 28 LEDs controlled by an ESP32 using Charlieplexing, designed in KiCad.
This project is a decorative PCB in the shape of a heart, featuring 28 LEDs driven directly from an ESP32 using the Charlieplexing technique — no shift registers or extra ICs needed. The board was designed from scratch in KiCad.
- 28 LEDs arranged in a heart silhouette - Charlieplexing with 8 GPIO pins (8×7 = 56 combinations → 28 LEDs used) - ESP32 as the main controller - Programmable LED animations - Powered via USB

Main components on the LED HEART
LED HEART bill of materials (BOM)
30 components, 3 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM | ESP32-C3-DevKitC-02_1 | U1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 28 | LD271 | LED_D5.0mm_IRGrey | D1, D2, D3, D4, D5, D6, D7, D8 +20 |
LED HEART design files
The KiCad project lives in the zukunho/LED_HEART repository on GitHub; these links point at the commit this page was built from.
LED HEART: common questions
What microcontroller does the LED HEART use?
The LED HEART is built around the ESP32-WROOM, from the ESP32 family.
How big is the LED HEART PCB?
The LED HEART measures 114.9 × 105.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LED HEART?
30 components, from 3 distinct parts. The full bill of materials is listed on this page.
Where can I download the LED HEART design files?
From the zukunho/LED_HEART repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the LED HEART design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which zukunho chose for the repository.
Can I test firmware for the LED HEART without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k