Custom-Mixer-ESP32
3aks·Custom-Mixer-ESP32·Custom-Mixer-Kicad/Custom-Mixer-ESP32.kicad_pcb
About the Custom-Mixer-ESP32 PCB
Custom-Mixer-ESP32 is an open source ESP32 PCB design by 3aks, published on GitHub under the MIT license. It is a 2-layer board measuring 192.3 × 121.2 mm, with 39 components from 10 distinct parts.
Its main chip is the ESP32-S3-DevKitC, from the ESP32 family. Other key parts include the MCP23017_SP. By type, the board carries 20 switches, 8 capacitors, 3 resistors, 2 ICs and 1 connector.
From the project
A cool mixer that will be developed soon
This project uses an ESP32 to read 5 linear faders, 2 rotary encoders, and 18 switches, with programmable buttons acting like MIDI and everything that happens, as a change in volume will show on the 2.2-inch screen.
This project's purpose is to act as a mixer and control the volume of an app when it sounds too loud or too quiet.
The Rotary Encoders will be used as a selector to scroll through active apps and the slider they should be on, or potentially as a master volume control.
Main components on the Custom-Mixer-ESP32
Custom-Mixer-ESP32 bill of materials (BOM)
39 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DevKitC | ESP32-S3-DevKitC | U7 |
| 1 | MCP23017_SP | DIP-28_W7.62mm | U8 |
| 1 | Conn_01x08 | PinSocket_1x09_P2.54mm_Vertical | J1 |
| 5 | R_Potentiometer_Dual | Potentiometer_Bourns_PTA6043_Single_Slide | RV1, RV2, RV3, RV4, RV5 |
| 2 | RotaryEncoder_Switch | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW1, SW2 |
| 18 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10 +10 |
| 1 | 100µF | CP_Radial_D6.3mm_P2.50mm | C1 |
| 7 | 0.1µF | C_Disc_D5.0mm_W2.5mm_P2.50mm | C2, C3, C4, C5, C6, C7, C8 |
| 1 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 2 | 4.7K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3 |
Custom-Mixer-ESP32 design files
The KiCad project lives in the 3aks/Custom-Mixer-ESP32 repository on GitHub; these links point at the commit this page was built from.
Custom-Mixer-ESP32: common questions
What microcontroller does the Custom-Mixer-ESP32 use?
The Custom-Mixer-ESP32 is built around the ESP32-S3-DevKitC, from the ESP32 family.
How big is the Custom-Mixer-ESP32 PCB?
The Custom-Mixer-ESP32 measures 192.3 × 121.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Custom-Mixer-ESP32?
39 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Custom-Mixer-ESP32 design files?
From the 3aks/Custom-Mixer-ESP32 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Custom-Mixer-ESP32 design in my own project?
Yes, under the terms of its MIT license, which 3aks chose for the repository.
Can I test firmware for the Custom-Mixer-ESP32 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Custom-Mixer-ESP32
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k