RoboHand
9Akshit1·RoboHand·schematic_pcb/robohand/robohand.kicad_pcb

About the RoboHand PCB
RoboHand is an open source ESP32 PCB design by 9Akshit1, published on GitHub. It is a 2-layer board, with 17 components from 5 distinct parts.
Its main chip is the ESP32-CAM, from the ESP32 family. Other key parts include the ADS1115IDGS. By type, the board carries 10 modules, 2 ICs and 1 capacitor.
It belongs with the robotics & motion designs in this gallery.
From the project
INSPIRATION: I've always been inspired by how human hands move and wanted to recreate that motion using motors and tendons. Additionally, at the same time, I was learning how to simulate robots in physics based simulations called MuJoCo, which is why I wanted to also actaully bui
INSPIRATION: I've always been inspired by how human hands move and wanted to recreate that motion using motors and tendons. Additionally, at the same time, I was learning how to simulate robots in physics based simulations called MuJoCo, which is why I wanted to also actaully build a hand and test my inverse kinematics coding knowledge at it.
Note: I am currently working on polishing the CAD, so it's much thinner, models the human hand better, and allows for full movement!
Main components on the RoboHand
RoboHand bill of materials (BOM)
17 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-CAM | ESP32-CAM | U1 |
| 1 | ADS1115IDGS | TSSOP-10_3x3mm_P0.5mm | U7 |
| 10 | Motor_Servo | PinHeader_1x03_P2.54mm_Vertical | M1, M2, M3, M4, M5, M6, M7, M8 +2 |
| 4 | ~ | MyoWare EMG Sensor1, MyoWare EMG Sensor2, MyoWare EMG Sensor3, MyoWare EMG Sensor4 | |
| 1 | C_Polarized | CP_Radial_D5.0mm_P2.50mm | C1 |
RoboHand design files
The KiCad project lives in the 9Akshit1/RoboHand repository on GitHub; these links point at the commit this page was built from.
RoboHand: common questions
What microcontroller does the RoboHand use?
The RoboHand is built around the ESP32-CAM, from the ESP32 family.
How big is the RoboHand PCB?
The RoboHand has 2 copper layers and is 1.6 mm thick.
How many components are on the RoboHand?
17 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RoboHand design files?
From the 9Akshit1/RoboHand repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RoboHand design in my own project?
The repository has no license, so all rights stay with 9Akshit1. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the RoboHand without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k