Gpib breakout
About the Gpib breakout
Gpib breakout is an open source Raspberry Pi PCB design by abzman, published on GitHub under the Unlicense license. It is a 2-layer board measuring 51.7 × 66 mm, with 14 components from 13 distinct parts.
Its main chip is the Raspberry_Pi_2_3, from the Raspberry Pi family. Other key parts include the 7407 and SN75161BN. By type, the board carries 5 resistors, 3 connectors, 2 ICs, 2 diodes and 2 capacitors.
It belongs with the dev boards & breakouts designs in this gallery.
Main components on the Gpib breakout
Gpib breakout bill of materials (BOM)
14 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 7407 SN75160BN | DIP-20_W7.62mm | U1 |
| 1 | SN75161BN | DIP-20_W7.62mm | U2 |
| 1 | KMDGX-9S-BS-1 2x12 card edge connector (lettered/numbered) | edge mounted 24 pin card edge connector (2x12 pin) | J1 |
| 1 | 112-024-113R001 | GPIB | J2 |
| 1 | Raspberry_Pi_2_3 | PinHeader_2x20_P2.54mm_Vertical | J3 |
| 1 | 1N4148 Activity | C_0603_1608Metric | D1 |
| 1 | 1N4148 Power | C_0603_1608Metric | D2 |
| 2 | 100NF 0.1uF | C_0603_1608Metric | C1, C2 |
| 1 | 100 10K | R_0603_1608Metric | R1 |
| 1 | 470 10K | R_0603_1608Metric | R2 |
| 1 | 10K | R_0603_1608Metric | R3 |
| 1 | 1k | R_0603_1608Metric | R4 |
| 1 | 180 1k | R_0603_1608Metric | R5 |
Gpib breakout design files
The KiCad project lives in the abzman/small-useful-PCBs repository on GitHub; these links point at the commit this page was built from.
Gpib breakout: common questions
What microcontroller does the Gpib breakout use?
The Gpib breakout is built around the Raspberry_Pi_2_3, from the Raspberry Pi family.
How big is the Gpib breakout?
The Gpib breakout measures 51.7 × 66 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Gpib breakout?
14 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Gpib breakout design files?
From the abzman/small-useful-PCBs repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Gpib breakout design in my own project?
Yes, under the terms of its Unlicense license, which abzman chose for the repository.
Can I test firmware for the Gpib breakout without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
More boards in small-useful-PCBs
Odyssey 2 rgb
83.3 × 78.2 mm70 parts2LUnlicense19
AVR/ArduinoAtmega16 breakout
111.8 × 88.9 mm44 parts2LUnlicense19
Xc9572 breakout
50.8 × 43.2 mm43 parts2LUnlicense19
Ttl to composite video generator
59.7 × 37.5 mm29 parts2LUnlicense19
Radio Shack Mini Speaker work alike
41.3 × 60.3 mm24 parts2LUnlicense19
4x relay board
61 × 47 mm24 parts2LUnlicense19
3do switch
43.2 × 20.6 mm19 parts2LUnlicense19
556 power on reset
32.4 × 22.2 mm14 parts2LUnlicense19
Spi led breakout
93.7 × 43.2 mm14 parts2LUnlicense19
Cord reel detent ring
33.4 × 27.2 mm5 parts2LUnlicense19
SEM card breakout
253.9 × 360.7 mm4 parts2LUnlicense19
Similar boards
Raspberry PiHaxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license672
Raspberry PiDesktop 50 Pin TopConn
BlueSCSI
89.2 × 82.6 mm103 parts2LGPL-3.0449
Raspberry PiPowerBook
74.5 × 56.3 mm78 parts2LGPL-3.0449
Raspberry PiBitDogLab 5.4
BitDogLab
87.9 × 123.9 mm56 parts2LCERN-OHL-S-2.0201
Raspberry PiBitDogLab Main SMD version
87.9 × 98.7 mm124 parts2LCERN-OHL-S-2.0201
Raspberry PiZynthian mini v2 20 buttons short
zynthian
163 × 120 mm87 parts2LNo license154