Curupira diy

acacio90·curupira-diy

Curupira diy PCB layout, top view — open source ESP32 board by acacio90

About the Curupira diy PCB

Curupira diy is an open source ESP32 PCB design by acacio90, published on GitHub. It is a 2-layer board measuring 100 × 100 mm, with 31 components from 25 distinct parts.

Its main chip is the ESP32-S3-DEVKITC, from the ESP32 family. Other key parts include the TSOP38238. By type, the board carries 9 resistors, 8 connectors, 5 switches, 4 diodes, 2 ICs and 2 capacitors.

It belongs with the rf & radio, iot & wireless and power & battery designs in this gallery.

From the project

Dispositivo portátil estilo Cardputer rodando Bruce — ESP32-S3, feito pra montar à mão (THT).

Dispositivo portátil estilo Cardputer rodando Bruce — ESP32-S3, feito pra montar à mão (THT).

CURUPIRA é uma PCB DIY, inspirada no M5Stack Cardputer, projetada no KiCad para rodar o firmware Bruce num ESP32-S3-DevKitC-1 (N16R8). O foco é um "canivete suíço" de RF/pentest de estudo, soldável à mão (componentes through-hole + DevKit encaixável, sem SMD).

- v0.4.1 — placa 100×100 mm (2 camadas), 4 furos M3, roteada e com DRC limpo (0 violações). Gerbers em production/curupira-v0.4.1-gerbers-jlcpcb.zip. - v0.4.1 (correção): removida 1 via de GND que ficava sobre o furo do J9-1 (furos…

Curupira diy, from the project README
From the project README

Main components on the Curupira diy

Curupira diy bill of materials (BOM)

31 components, 25 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-DEVKITC
ESP32-S3-DevKitC
U1
1
TSOP38238
U2
1
BC337
Q1
1
TFT_ST7789
J1
1
I2C_QWIIC
I2C_Qwiic
J2
1
CC1101
J3
1
SD_MODULE
J4
1
BAT_TP4056
J5
1
GPS_UART
J6
1
I2C_EXTRA
J8
1
NRF24L01_PA_LNA
J9
1
CIMA
SW1
1
BAIXO
SW2
1
OK
SW3
1
VOLTAR
SW4
1
LIGA
SW5
1
LED
D1
1
1N5817
D2
2
IR_940NM
IR_940nm
D3, D5
2
100N
100n
C1, C2
Show 5 more
QtyPartRefs
1
330
R1
2
22
R2, R10
1
1k
R3
2
100K
100k
R4, R5
3
10K
10k
R6, R7, R8

Curupira diy design files

The KiCad project lives in the acacio90/curupira-diy repository on GitHub; these links point at the commit this page was built from.

Curupira diy: common questions

What microcontroller does the Curupira diy use?

The Curupira diy is built around the ESP32-S3-DEVKITC, from the ESP32 family.

How big is the Curupira diy PCB?

The Curupira diy measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Curupira diy?

31 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Curupira diy design files?

From the acacio90/curupira-diy repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Curupira diy design in my own project?

The repository has no license, so all rights stay with acacio90. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Curupira diy without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards