Falcon

Adnanosman9·Falcon·PCB/drone.kicad_pcb

Falcon PCB layout, top view — open source STM32 board by Adnanosman9

About the Falcon PCB

Falcon is an open source STM32 PCB design by Adnanosman9, published on GitHub under the MIT license. It is a 4-layer board measuring 46.8 × 44.7 mm, with 75 components from 30 distinct parts.

Its main chip is the STM32H743VIT6, from the STM32 family. Other key parts include the BMI088, FM25V02A-GTR, USBLC6-2SC6, BMP390 and AP2112K-3.3TRG1. By type, the board carries 28 capacitors, 28 resistors, 7 ICs, 7 connectors, 2 crystals and 2 inductors.

It belongs with the robotics & motion and power & battery designs in this gallery.

From the project

FC Falcon, a custom, STM32H7 powered flight controller designed specifically for high precision architectural photogrammetry. It delivers vibration isolated stability required to execute centimeter accurate precision.

I wanted to build a drone that could do proper 3D photogrammetry surveys. Off-the-shelf F4 flight controllers don't have enough processing power for the EKF configuration I need when fusing RTK GPS with IMU data at high rates. So I designed my own.

This is a flight controller built around the STM32H743VIT6 , a 480MHz Cortex-M7 chip with 2MB flash and 1MB RAM. It runs a custom-compiled ArduPilot firmware with pin mappings specific to this board.

Main components on the Falcon

Falcon bill of materials (BOM)

75 components, 30 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32H743VIT6
U1
1
BMI088
U2
1
FM25V02A-GTR
U3
1
USBLC6-2SC6
U4
1
BMP390
U5
1
AP2112K-3.3TRG1
U8
1
MP1584EN
U9
1
ABM8-272-T3
Y1
1
CM315D32768DZFT
Y2
1
104031-0811
J1
1
USB-C
J2
2
BM04B-GHS-TBT
J3, J7
2
BM06B-GHS-TBT
J4, J6
1
BDL-108-X-X
J5
1
D_Schottky
D1
1
LPS4018-103
L1
1
L_Ferrite
L2
18
C0402C104K3RACTU
C1, C2, C3, C4, C5, C6, C7, C8 +10
2
GRM188R61C225KE15D
C17, C23
2
GRM155R61E105KA12D
C18, C24
Show 10 more
QtyPartRefs
2
GRM1555C1H180JA01D
C19, C20
2
GRM1555C1H7R0DA01D
C21, C22
1
GRM21BR61A226ME51L
C26
1
GRM1555C1H222JA01D
C28
5
RC0402FR-07100KL
R1, R5, R8, R10, R25
4
RC0402FR-07100RL
R2, R7, R15, R21
12
RC0402FR-0710KL
R3, R6, R12, R17, R18, R19, R20, R26 +4
2
RC0402FR-075K1L
R4, R11
1
RC0402FR-0720KL
R9
4
RC0402FR-072K2L
R16, R22, R23, R24

Falcon design files

The KiCad project lives in the Adnanosman9/Falcon repository on GitHub; these links point at the commit this page was built from.

Falcon: common questions

What microcontroller does the Falcon use?

The Falcon is built around the STM32H743VIT6, from the STM32 family.

How big is the Falcon PCB?

The Falcon measures 46.8 × 44.7 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Falcon?

75 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Falcon design files?

From the Adnanosman9/Falcon repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Falcon design in my own project?

Yes, under the terms of its MIT license, which Adnanosman9 chose for the repository.

Can I test firmware for the Falcon without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards