PROMETHEUS-1 Ground Station

AFS-pt·PROMETHEUS-1·3.GroundStation/GS_UMinho/GS_RPi/Hardware/v2/RPi GS hat board.kicad_pcb

PROMETHEUS-1 Ground Station PCB layout, top view — open source Raspberry Pi board by AFS-pt

About the PROMETHEUS-1 Ground Station PCB

PROMETHEUS-1 Ground Station is an open source Raspberry Pi PCB design by AFS-pt, published on GitHub. It is a 2-layer board measuring 65 × 45 mm, with 26 components from 21 distinct parts.

Its main chip is the Raspberry_Pi_2_3, from the Raspberry Pi family. Other key parts include the RFM98PW and AZ2185D-ADJTRG1n. By type, the board carries 8 resistors, 7 connectors, 6 capacitors, 2 ICs and 1 diode.

It belongs with the rf & radio and dev boards & breakouts designs in this gallery.

From the project

Documentation lives here: https://afs-pt.github.io/PROMETHEUS-1

A small modular radio to chat with satellites.

- LoRa UHF communication (TX and RX); - Compatible with Raspberry Pi (40-pin header); - Programmed with CircuitPython; - Independent power supply to increase performance; - Dedicated to PROMETHEUS-1 satellite.

For more details on the RFM98 radio module, check the short and detailed datasheets.

A few issues from RPiGS v2 were discovered during testing, which could be fixed in a new iteration (v2.1). These issues are detailed below:

Main components on the PROMETHEUS-1 Ground Station

RFM98PWAZ2185D-ADJTRG1n

PROMETHEUS-1 Ground Station bill of materials (BOM)

26 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RFM98PW
U1
1
AZ2185D-ADJTRG1n
U2
1
Raspberry_Pi_2_3
J1
1
Coax SMA
J2
1
Barrel_Jack
J3
1
VCC
J4
1
V_REG
J5
1
GND
J6
1
3.3V
J7
1
5K
3296W-1-502LF1
1
3A
ERBRG3R00V1
1
POW
D1
3
0.1uF
C1, C5, C6
1
10uF
C2
1
10uF
C3
1
22uF
C4
2
10K
R1, R2
1
2.8K
R3
1
8.2K
R4
1
200
R5
Show 1 more
QtyPartRefs
3
0
R10, R11, R12

PROMETHEUS-1 Ground Station design files

The KiCad project lives in the AFS-pt/PROMETHEUS-1 repository on GitHub; these links point at the commit this page was built from.

PROMETHEUS-1 Ground Station: common questions

What microcontroller does the PROMETHEUS-1 Ground Station use?

The PROMETHEUS-1 Ground Station is built around the Raspberry_Pi_2_3, from the Raspberry Pi family.

How big is the PROMETHEUS-1 Ground Station PCB?

The PROMETHEUS-1 Ground Station measures 65 × 45 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PROMETHEUS-1 Ground Station?

26 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the PROMETHEUS-1 Ground Station design files?

From the AFS-pt/PROMETHEUS-1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the PROMETHEUS-1 Ground Station design in my own project?

The repository has no license, so all rights stay with AFS-pt. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the PROMETHEUS-1 Ground Station without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

More boards in PROMETHEUS-1

Similar boards