28 open source boards using the MCP6002-xP
Real designs built with the MCP6002-xP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Offshoots
MiguelDeTrool
30 × 128.3 mm49 parts2LGPL-3.026NXP
RC11-2
AgOpenGPS-Official
159 × 130 mm100 parts4LGPL-3.020AVR/Arduino
Tarbleming
MiguelDeTrool
71 × 128.5 mm91 parts2LCustom license14AVR/Arduino
Zuendbox v3 32
fixxl
213.6 × 127.5 mm153 parts2LNo license1010band nixie
davemuscle
274.1 × 114.7 mm312 parts2LNo license7STM32
Bit Crusher Pedal
JordanAceto
81.3 × 61 mm94 parts2LNo license2ESP32
Tbogg-Sensor-Package
UofC-GNCTR-2024
52 × 67 mm40 parts2LMIT1- schematic only · 102 parts
LaserDiodeDriver Hardware
MissouriMRDT
102 partsGPL-3.01 AVR/Arduino
Campervan management V2.1
akladnig
169.5 × 96 mm168 parts4LNo license0AVR/Arduino
AVML: PCB1 & PCB2
joem
37.5 × 100 mm74 parts2LNo license0ESP32
Microcontroller Schematics
AlexFinns
79.4 × 70 mm49 parts2LNo license0Uno Shield DSP Class v1
cshieldsce
83.8 × 53.3 mm46 parts2LNo license0Uno Shield DSP Class v1
LandryEllis
68.6 × 53.3 mm46 parts2LNo license0Uno Shield DSP
laurenoo
68.6 × 53.3 mm46 parts2LNo license0Arduino shield
nruth633
83.8 × 53.3 mm46 parts2LNo license0ESP32
Carte2
Honzaaa45
136.3 × 88.3 mm44 parts2LMIT0AVR/Arduino
Can atmega layout-2025-07-01
Zwackelmann
111 × 150 mm39 parts2LNo license0RP2040/RP2350
0xEntropy
dudleydehenau
163.5 × 40.5 mm38 parts2LNo license0AVR/Arduino
Semiconductor parameter daq bench
Divyansh12-86
162 × 100 mm24 parts2LNo license0Oscilite
st4rk-7
92 × 118 mm22 parts2LNo license0ESP32
Esp32-sensor daq
EldinLz
73.5 × 65.5 mm16 parts2LNo license0- schematic only · 41 parts
Orbita26
notazizelse
41 partsNo license0 DaisyDelayHardwareTestRoute
fablabnk
30 × 128.5 mm49 parts2LNo license3Uno Shield For NASA
LandryEllis
68.6 × 53.3 mm30 parts2LNo license0SMD Microcontroller Schematics
AlexFinns
78.7 × 59.7 mm28 parts4LNo license0- schematic only · 253 partsAVR/Arduino
Camper van
akladnig
253 parts2LNo license0 Can atmega-02-layout2
Zwackelmann
114 × 56 mm16 parts2LNo license0AVR/Arduino
Temp module
Zwackelmann
37 × 27 mm15 parts2LNo license0
How designs wire the MCP6002-xP
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the MCP6002-xP connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 20 of 21 designs.
- Pin 1 has a series resistor on 16 of 21 designs, most often 1 kΩ (then 100 kΩ).
- The - pins have a series resistor on 16 of 21 designs, most often 100 kΩ (then 20 kΩ).
- The V+ pin has a decoupling capacitor on 12 of 20 designs, most often 100 nF (then 47 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 24% |
|
| -pin 2, 6 | Connected to: Signal 76% · not connected 20% |
|
| +pin 3, 5 | Connected to: Signal 59% · GND 34% |
|
| V-pin 4 | Connected to: GND 95% | — |
| Pin 7 | Connected to: The microcontroller 20% · not connected 45% |
|
| V+pin 8 | Connected to: 5V 95% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Offshoots by MiguelDeTrool, RC11-2 by AgOpenGPS-Official, Tarbleming by MiguelDeTrool and Zuendbox v3 32 by fixxl.
The MCP6002-xP in open source designs
The gallery holds 28 open source boards using the MCP6002-xP from 23 GitHub repositories; a typical one measures about 81.3 × 70 mm and carries around 46 components.
88% are two-layer designs, the rest use four layers or more, and 18% carry an open source license.
The most starred is Offshoots by MiguelDeTrool.
Parts used alongside the MCP6002-xP
Microcontrollers on boards using the MCP6002-xP
What boards using the MCP6002-xP are built for
MCP6002-xP: common questions
Where can I find a MCP6002-xP reference design?
Each of the 28 boards on this page is a real design using the MCP6002-xP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MCP6002-xP V- pin connected?
The V- pin is tied to GND on 20 of 21 designs. Counted from the KiCad layouts of 21 open source designs using the MCP6002-xP.
What resistor goes on the MCP6002-xP pin 1?
Pin 1 has a series resistor on 16 of 21 designs, most often 1 kΩ (then 100 kΩ). Counted from the KiCad layouts of 21 open source designs using the MCP6002-xP.
What resistor goes on the MCP6002-xP - pin?
The - pins have a series resistor on 16 of 21 designs, most often 100 kΩ (then 20 kΩ). Counted from the KiCad layouts of 21 open source designs using the MCP6002-xP.
What parts are used alongside the MCP6002-xP?
The Arduino_Nano_v3.x, L7805, LM4040LP-5, AMS1117-3.3 and DS18B20 appear in the most repositories here.
Which microcontrollers do boards using the MCP6002-xP use?
Most are built on AVR/Arduino (9), ESP32 (4), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the MCP6002-xP?
The median is 81.3 × 70 mm, and 88% are two-layer designs.
What is the most popular open source board using the MCP6002-xP?
By GitHub stars, Offshoots by MiguelDeTrool, with 26 stars.
Can I simulate one of these boards using the MCP6002-xP before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.