21 open source boards using the MCP2562-E-P
Real designs built with the MCP2562-E-P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
NXP
RC11-2
AgOpenGPS-Official
159 × 130 mm100 parts4LGPL-3.020CTA control board
PySpice-org
252 × 152 mm614 parts4LNo license9NXP
V4.2
brunob45
48.9 × 52.7 mm49 parts2LNo license5STM32
LEDNip
MayaPosch
90 × 100 mm148 parts4LBSD-3-Clause3ESP32
E28-cluster
dowster
130.8 × 139.7 mm74 parts2LNo license3ESP32
PowerControlBoard
takaki-maeda-99
100 × 85 mm108 parts4LNo license1ESP32
Esp32-ecu
markthebault
120 × 120 mm214 parts6LNo license0STM32
NMEA-2000-Battery-Power
hoellwerth
180.3 × 100.3 mm96 parts4LNo license0PIC
Kicad
PoJD
55 × 45 mm23 parts2LApache-2.00NXP
V4.1
brunob45
48.9 × 52.7 mm48 parts2LNo license5NXP
SMCSKart-Mainboard
PHS-SMCS
128.3 × 94 mm64 parts4LNo license1NXP
V4.0
brunob45
48.9 × 52.7 mm43 parts2LNo license5STM32
Board stm32 rev2
SuzieLinux
100 × 100 mm37 parts2LGPL-3.00Nucleo can md2 roricon2
NiiRoboKen
63.7 × 58.6 mm16 parts2LNo license0NXP
V3.0
brunob45
39.4 × 52.1 mm37 parts2LNo license5NXP
V2.0
brunob45
40 × 52.7 mm36 parts2LNo license5NXP
V2.1
brunob45
40 × 52.7 mm36 parts2LNo license5NXP
V2.2
brunob45
39.4 × 52.1 mm36 parts2LNo license5PocketBeagle2Cape rev1
SuzieLinux
101.8 × 55.3 mm27 parts2LGPL-3.00NXP
V1.0
brunob45
40 × 52.7 mm29 parts2LNo license5AVR/Arduino
PocketBeagle2 cape
SuzieLinux
101.8 × 55.3 mm25 parts2LGPL-3.00
How designs wire the MCP2562-E-P
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the MCP2562-E-P connects to, and the resistors, capacitors and other passives placed on it.
- The CANL pin has a series resistor on 7 of 12 designs, most often 120 Ω (then 0 Ω).
- The CANH pin has a series resistor on 7 of 12 designs, most often 120 Ω (then 0 Ω).
- The VDD pin has a decoupling capacitor on 6 of 12 designs, most often 100 nF (then 4.7 µF).
- The VIO pin has a decoupling capacitor on 5 of 12 designs, most often 100 nF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 92% | — |
| VDDpin 3 | Connected to: 5V 100% |
|
| VIOpin 5 | Connected to: 3.3V 83% · a signal 17% |
|
| CANLpin 6 | Connected to: A connector 92% |
|
| CANHpin 7 | Connected to: A connector 92% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RC11-2 by AgOpenGPS-Official, CTA control board by PySpice-org, V1.0 by brunob45 and E28-cluster by dowster.
The MCP2562-E-P in open source designs
The gallery holds 21 open source boards using the MCP2562-E-P from 12 GitHub repositories; a typical one measures about 90 × 55.3 mm and carries around 43 components.
67% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is RC11-2 by AgOpenGPS-Official.
Parts used alongside the MCP2562-E-P
Microcontrollers on boards using the MCP2562-E-P
What boards using the MCP2562-E-P are built for
MCP2562-E-P: common questions
Where can I find a MCP2562-E-P reference design?
Each of the 21 boards on this page is a real design using the MCP2562-E-P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP2562-E-P CANL pin?
The CANL pin has a series resistor on 7 of 12 designs, most often 120 Ω (then 0 Ω). Counted from the KiCad layouts of 12 open source designs using the MCP2562-E-P.
What resistor goes on the MCP2562-E-P CANH pin?
The CANH pin has a series resistor on 7 of 12 designs, most often 120 Ω (then 0 Ω). Counted from the KiCad layouts of 12 open source designs using the MCP2562-E-P.
What decoupling capacitors do designs use on the MCP2562-E-P VDD pin?
The VDD pin has a decoupling capacitor on 6 of 12 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 12 open source designs using the MCP2562-E-P.
Which microcontrollers do boards using the MCP2562-E-P use?
Most are built on NXP (10), ESP32 (3), STM32 (3) and AVR/Arduino (1).
How big is a typical board using the MCP2562-E-P?
The median is 90 × 55.3 mm, and 67% are two-layer designs.
What is the most popular open source board using the MCP2562-E-P?
By GitHub stars, RC11-2 by AgOpenGPS-Official, with 20 stars.
Can I simulate one of these boards using the MCP2562-E-P before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.