HardLabs

PCB2 OrganNode

ahaimour2005·BSF_Engineering_Better_Health-Medi_Development·System_Design/PCBs/PCB2_OrganNode/out/PCB2_OrganNode/PCB2_OrganNode.kicad_pcb

PCB2 OrganNode PCB layout, top view — open source AVR/Arduino board by ahaimour2005
Simulate this board

About the PCB2 OrganNode PCB

PCB2 OrganNode is an open source AVR/Arduino PCB design by ahaimour2005, published on GitHub under the MIT license. It is a 2-layer board measuring 35 × 47 mm, with 7 components from 7 distinct parts.

Its main chip is the Arduino Nano Every, from the AVR/Arduino family. By type, the board carries 5 connectors, 1 module and 1 capacitor.

It belongs with the displays & leds designs in this gallery.

From the project

MEDI is an interactive museum exhibit: a model human body where visitors press a button on a "pod" and the matching organ lights up. This repository holds everything for it: the firmware, the custom PCBs, the heart-rate sensor work that started the project, and the notes and data

MEDI is an interactive museum exhibit: a model human body where visitors press a button on a "pod" and the matching organ lights up. This repository holds everything for it: the firmware, the custom PCBs, the heart-rate sensor work that started the project, and the notes and datasheets behind them.

- Pods are wireless button boards placed around the room. One pod per organ (11 pods). - The conductor listens for pod presses and sends state commands (IDLE, HIGHLIGHT, PULSE, BLACKOUT) down a one-way wired bus. - Organ nodes each drive their own LED strip (NeoPixel) and own their animation…

Main components on the PCB2 OrganNode

Arduino Nano Every

PCB2 OrganNode bill of materials (BOM)

7 components, 7 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Arduino Nano Every
A1
1
CONN_01X04_PIN
Conn_01x04_Pin
J1
1
CONN_02X04_ODD_EVEN
Conn_02x04_Odd_Even
J2
1
TX/RX/GND (top)
J3
1
TX/RX/GND (bottom)
J4
1
TX/RX/GND (bottom)
J7
1
100nF 50V
C2

PCB2 OrganNode design files

The KiCad project lives in the ahaimour2005/BSF_Engineering_Better_Health-Medi_Development repository on GitHub; these links point at the commit this page was built from.

PCB2 OrganNode: common questions

What microcontroller does the PCB2 OrganNode use?

The PCB2 OrganNode is built around the Arduino Nano Every, from the AVR/Arduino family.

How big is the PCB2 OrganNode PCB?

The PCB2 OrganNode measures 35 × 47 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PCB2 OrganNode?

7 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the PCB2 OrganNode design files?

From the ahaimour2005/BSF_Engineering_Better_Health-Medi_Development repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the PCB2 OrganNode design in my own project?

Yes, under the terms of its MIT license, which ahaimour2005 chose for the repository.

Can I test firmware for the PCB2 OrganNode without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in BSF_Engineering_Better_Health-Medi_Development

Similar boards