Starcade35
aishahisap123-code·starcade35·starbie/_restore_backup_2026-10-07T20-12-16-564/starbie.kicad_pcb
About the Starcade35 PCB
Starcade35 is an open source ESP32 PCB design by aishahisap123-code, published on GitHub under the MIT license. It is a 2-layer board measuring 143.6 × 71.8 mm, with 18 components from 11 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 6 diodes, 3 switches, 3 resistors, 2 ICs, 2 connectors and 1 buzzer.
From the project
this is week one for hackclub's halflife hardware program
Main components on the Starcade35
Starcade35 bill of materials (BOM)
18 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | MCU_Seeed_ESP32C3 | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | Conn_01x08_Pin | MPU6050_Module | J1 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J2 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 2 | SW_Push | SW_PUSH_6mm | SW1, SW2 |
| 1 | RotaryEncoder_Switch | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW3 |
| 6 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6 |
| 1 | C_Polarized | CP_Radial_D8.0mm_P3.50mm | C2 |
| 2 | 4.7k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R3 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2 |
Starcade35 design files
The KiCad project lives in the aishahisap123-code/starcade35 repository on GitHub; these links point at the commit this page was built from.
Starcade35: common questions
What microcontroller does the Starcade35 use?
The Starcade35 is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starcade35 PCB?
The Starcade35 measures 143.6 × 71.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starcade35?
18 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starcade35 design files?
From the aishahisap123-code/starcade35 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starcade35 design in my own project?
Yes, under the terms of its MIT license, which aishahisap123-code chose for the repository.
Can I test firmware for the Starcade35 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k