MiniConsoleCarrier
albash0·MiniConsole·MiniConsole/PCB/MiniConsoleCarrier.kicad_pcb
About the MiniConsoleCarrier PCB
MiniConsoleCarrier is an open source ESP32 PCB design by albash0, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 70.1 × 30.1 mm, with 24 components from 17 distinct parts.
Its main chip is the ESP32-S3 SuperMini, from the ESP32 family. By type, the board carries 7 switches, 5 connectors, 1 IC, 1 capacitor and 1 resistor.
It belongs with the displays & leds and iot & wireless designs in this gallery.
From the project
ESP32-S3 handheld: OLED/TFT firmware, custom PCBs, printable enclosure, wireless co-op and automated tests. Personal engineering project.
Open MiniConsoleCarrier.kicadpro` in KiCad 10. The checked schematic, routed PCB, local symbols/footprints and unpacked manufacturing outputs are included. Use the native KiCad design as the authority; the EAGLE/Fusion interchange files may require copper-polygon regeneration and DRC after import.
The carrier is 70.1 × 30.1 mm with a 65.9 × 26.1 mm case mounting pattern. This revision adds five rear test pads and moves Left/Right inward 0.50 mm each. The expansion header is above Up. VCC and logic are 3.3 V. See documentation/BOM.csv, manufacturing/, and the retained geometry/check reports…
Main components on the MiniConsoleCarrier
MiniConsoleCarrier bill of materials (BOM)
24 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3 SuperMini | S3_Rear_USB_Down_2x09 | U1 |
| 1 | OLED SDA SCL VCC GND | OLED_1x04 | J1 |
| 1 | BATTERY wires | Wire_2x_2.54_Reverse | J2 |
| 1 | To S3 B+/B- | Wire_2x_2.54 | J3 |
| 1 | External piezo (optional) | Wire_2x_2.54_Reverse | J4 |
| 1 | IIC GND VCC SCL SDA | IIC_1x04 | J5 |
| 1 | SMT-0940-T-3V-R (optional) | Piezo_PUI_SMT0940_180 | B1 |
| 8 | M2 clearance | Mount_M2 | H1, H2, H3, H4, H5, H6, H7, H8 |
| 1 | UP | SW_6mm | SW1 |
| 1 | DOWN | SW_6mm | SW2 |
| 1 | LEFT | SW_6mm_90 | SW3 |
| 1 | RIGHT | SW_6mm_90 | SW4 |
| 1 | A | SW_6mm | SW5 |
| 1 | B | SW_6mm | SW6 |
| 1 | BATTERY ON/OFF SS12D00 | SS12D00_LeftEdge_3pin | SW7 |
| 1 | 100nF | C_0603_180 | C1 |
| 1 | 220R | R_Axial_DIN0207_P7.62_220R | R1 |
MiniConsoleCarrier design files
The KiCad project lives in the albash0/MiniConsole repository on GitHub; these links point at the commit this page was built from.
MiniConsoleCarrier: common questions
What microcontroller does the MiniConsoleCarrier use?
The MiniConsoleCarrier is built around the ESP32-S3 SuperMini, from the ESP32 family.
How big is the MiniConsoleCarrier PCB?
The MiniConsoleCarrier measures 70.1 × 30.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MiniConsoleCarrier?
24 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MiniConsoleCarrier design files?
From the albash0/MiniConsole repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the MiniConsoleCarrier design in my own project?
Yes, under the terms of its GPL-2.0 license, which albash0 chose for the repository.
Can I test firmware for the MiniConsoleCarrier without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in MiniConsole
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k