OpenAC-IR
AlessandroBerrone·OpenAC-IR·hardware/openac-ir.net
About the OpenAC-IR PCB
OpenAC-IR is an open source ESP32 PCB design by AlessandroBerrone, published on GitHub under the MIT license. It is a board, with 10 components from 9 distinct parts.
Its main chip is the ESP32 DevKit V1, from the ESP32 family. Other key parts include the TSOP4838. By type, the board carries 3 capacitors, 3 resistors, 2 ICs, 1 transistor and 1 diode.
From the project
The authoritative, machine-readable description is circuit.yaml. circuit.json, netlist.txt, openac-ir.net, BOM.csv, pinout.csv and schematic.svg are human/tool-oriented representations of the same design.
The authoritative, machine-readable description is circuit.yaml. circuit.json, netlist.txt, openac-ir.net, BOM.csv, pinout.csv and schematic.svg are human/tool-oriented representations of the same design.
C1/C2 are connected to the 5 V rail before the R2+R3 pair.
For TSOP48 packages, viewed from the front/lens side, the datasheet pin order is 1 OUT, 2 GND, 3 VS. Always verify the exact part and orientation before soldering.
Main components on the OpenAC-IR
OpenAC-IR bill of materials (BOM)
10 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32 DevKit V1 | U1 | |
| 1 | TSOP4838 | U2 | |
| 1 | 2N2222A | Q1 | |
| 1 | TSAL6400 | D1 | |
| 2 | 100nF | C1, C3 | |
| 1 | 100uF | C2 | |
| 1 | 330R | R1 | |
| 1 | 22R | R2 | |
| 1 | 10R | R3 |
OpenAC-IR design files
The KiCad project lives in the AlessandroBerrone/OpenAC-IR repository on GitHub; these links point at the commit this page was built from.
- Netlisthardware/openac-ir.net
- BOMhardware/BOM.csv
OpenAC-IR: common questions
What microcontroller does the OpenAC-IR use?
The OpenAC-IR is built around the ESP32 DevKit V1, from the ESP32 family.
How many components are on the OpenAC-IR?
10 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the OpenAC-IR design files?
From the AlessandroBerrone/OpenAC-IR repository on GitHub, which has a netlist and the BOM; the links under Design files point to each one.
Can I use the OpenAC-IR design in my own project?
Yes, under the terms of its MIT license, which AlessandroBerrone chose for the repository.
Can I test firmware for the OpenAC-IR without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k