Rp2354-fcu

alvgaona·rp2354-fcu·hw/fc.kicad_pcb

Rp2354-fcu PCB layout, top view — open source Raspberry Pi board by alvgaona

About the Rp2354-fcu PCB

Rp2354-fcu is an open source Raspberry Pi PCB design by alvgaona, published on GitHub under the MIT license. It is a 2-layer board measuring 40 × 40 mm, with 63 components from 38 distinct parts.

Its main chip is the RP2354A, from the Raspberry Pi family. Other key parts include the AP63203WU-7 and ICM-42688-P. By type, the board carries 23 capacitors, 18 resistors, 12 connectors, 3 ICs, 3 diodes and 2 inductors.

It belongs with the robotics & motion, rf & radio and sensors designs in this gallery.

From the project

A 40 × 40 mm flight control unit built around the RP2354A.

A 40 × 40 mm flight control unit built around the RP2354A.

rp2354-fcu is a 2-layer flight controller that fits the 30.5 mm mounting pattern. It takes a 2S LiPo or USB, reads an IMU and a GPS, and drives eight servos or ESCs.

- RP2354A microcontroller with 2 MB of flash in the package - ICM-42688-P IMU on SPI - GPS connector (JST-GH) for an off-board module such as the NEO-6M - Eight 3-pin servo/ESC outputs - 2S LiPo (JST-XH) or USB-C power through a 3.3 V buck converter - SWD on JST-SH in the Raspberry Pi debug probe pinout

Main components on the Rp2354-fcu

Rp2354-fcu bill of materials (BOM)

63 components, 38 distinct parts.

QtyPartRefs
1
RP2354A
Raspberry Pi
U1
1
AP63203WU-7
AP63203WU
Diodes Inc
U2
1
ICM-42688-P
TDK InvenSense
U3
1
ABM8-272-T3
12MHz
Abracon
X1
1
TYPE-C-31-M-12
USB-C
HRO
J1
1
SM03B-SRSS-TB(LF)(SN)
SWD
JST
J4
1
SM04B-GHS-TB(LF)(SN)
GPS
JST
J5
1
B2B-XH-A(LF)(SN)
2S LiPo
JST
J6
1
2.54-1*3P
OUT1
BOOMELE
J7
1
2.54-1*3P
OUT2
BOOMELE
J8
1
2.54-1*3P
OUT3
BOOMELE
J9
1
2.54-1*3P
OUT4
BOOMELE
J10
1
2.54-1*3P
OUT5
BOOMELE
J11
1
2.54-1*3P
OUT6
BOOMELE
J12
1
2.54-1*3P
OUT7
BOOMELE
J13
1
2.54-1*3P
OUT8
BOOMELE
J14
1
434133025816
BOOTSEL
Wurth Elektronik
SW1
2
B5819W SL
B5819W
CJ
D1, D2
1
KT-0603R
RED
Hubei KENTO
D3
1
AOTA-B201610S3R3-101-T
3.3u
Abracon
L1
Show 18 more
QtyPartRefs
1
FNR3015S3R9MT
3.9u
Changjiang
L2
1
CL21A106KAYNNNE
10u
Samsung
C1
3
CL05B104KO5NNNC
100n
Samsung
C2, C20, C21
2
GRM1555C1H150JA01D
15p
Murata
C3, C4
2
CL21A226MAQNNNE
22u
Samsung
C5, C19
2
GRM155R60J475ME47D
4.7u
Murata
C6, C7
10
CL05B104KO5NNNC
100n
Samsung
C8, C10, C11, C12, C13, C14, C15, C16 +2
1
GRM155R60J475ME47D
4.7u
Murata
C9
1
CL05A225MQ5NSNC
2.2u
Samsung
C22
1
CL05B103KB5NNNC
10n
Samsung
C23
2
0402WGF5101TCE
5.1k
UNI-ROYAL
R1, R5
1
0402WGF1001TCE
1k
UNI-ROYAL
R2
1
0402WGF330JTCE
33
UNI-ROYAL
R3
2
0402WGF1001TCE
1k
UNI-ROYAL
R6, R19
2
0402WGF270JTCE
27
UNI-ROYAL
R7, R8
1
0402WGF1002TCE
10k
UNI-ROYAL
R9
1
0402WGF3301TCE
3.3k
UNI-ROYAL
R10
8
0402WGF2200TCE
220
UNI-ROYAL
R11, R12, R13, R14, R15, R16, R17, R18

Rp2354-fcu design files

The KiCad project lives in the alvgaona/rp2354-fcu repository on GitHub; these links point at the commit this page was built from.

Rp2354-fcu: common questions

What microcontroller does the Rp2354-fcu use?

The Rp2354-fcu is built around the RP2354A, from the Raspberry Pi family.

How big is the Rp2354-fcu PCB?

The Rp2354-fcu measures 40 × 40 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rp2354-fcu?

63 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the Rp2354-fcu design files?

From the alvgaona/rp2354-fcu repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Rp2354-fcu design in my own project?

Yes, under the terms of its MIT license, which alvgaona chose for the repository.

Can I test firmware for the Rp2354-fcu without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

Similar boards