EquiSense-ForcePlatform
amalnathkp13-boop·EquiSense-ForcePlatform·hardware/kicad/EquiSense.kicad_pcb
About the EquiSense-ForcePlatform PCB
EquiSense-ForcePlatform is an open source ESP32 PCB design by amalnathkp13-boop, published on GitHub. It is a 2-layer board, with 46 components from 25 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the AMS1117-3.3 and HX711. By type, the board carries 13 resistors, 12 capacitors, 6 ICs, 6 connectors, 5 transistors and 2 diodes.
From the project
Low-cost four-load-cell force platform for Centre-of-Pressure balance assessment after minor lower-limb amputation (Vishwakarma Awards 2026-27)
A low-cost, battery-isolated 450 × 450 mm force platform that measures Centre-of-Pressure (CoP) sway at 80 Hz. It is built for balance assessment after minor lower-limb amputation (toe, ray, transmetatarsal) in district-level rehabilitation centres.
Team: Dhiyadharshini V. · Kaviashree Rangasamy · Kameshwaran V. · Lakshmi Praba M. Supervisor: Mrs. C. Radhika, AP/BME, Department of Biomedical Engineering Programme: Vishwakarma Awards 2026-27, Stage 2
Main components on the EquiSense-ForcePlatform
EquiSense-ForcePlatform bill of materials (BOM)
46 components, 25 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | AMS1117-3.3 | U2 | |
| 4 | HX711 | SOIC-16_3.9x9.9mm_P1.27mm | U3, U4, U5, U6 |
| 1 | ERM 10mm 3V | M1 | |
| 4 | S8550 | Q1, Q2, Q3, Q4 | |
| 1 | AO3400A | SOT-23 | Q5 |
| 1 | LoadCell_FL | J1 | |
| 1 | LoadCell_FR | J2 | |
| 1 | LoadCell_BL | J3 | |
| 1 | LoadCell_BR | J4 | |
| 1 | 18650 Shield V8 5V OUT | J5 | |
| 1 | USB-UART | J6 | |
| 1 | HAPTIC_ISOLATE | JP1 | |
| 1 | 1N4007 | D1 | |
| 1 | STATUS | D2 | |
| 5 | 10uF | C1, C10, C12, C14, C16 | |
| 1 | 22uF | C2 | |
| 1 | 1uF | C3 | |
| 5 | 100nF | C4, C11, C13, C15, C17 | |
| 2 | 10k | R1, R2 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1k | R3 | |
| 1 | 220R | R4 | |
| 1 | 100k | R5 | |
| 4 | 20k | R10, R12, R14, R16 | |
| 4 | 8.2k | R11, R13, R15, R17 |
EquiSense-ForcePlatform design files
The KiCad project lives in the amalnathkp13-boop/EquiSense-ForcePlatform repository on GitHub; these links point at the commit this page was built from.
EquiSense-ForcePlatform: common questions
What microcontroller does the EquiSense-ForcePlatform use?
The EquiSense-ForcePlatform is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the EquiSense-ForcePlatform PCB?
The EquiSense-ForcePlatform has 2 copper layers and is 1.6 mm thick.
How many components are on the EquiSense-ForcePlatform?
46 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the EquiSense-ForcePlatform design files?
From the amalnathkp13-boop/EquiSense-ForcePlatform repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the EquiSense-ForcePlatform design in my own project?
The repository has no license, so all rights stay with amalnathkp13-boop. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the EquiSense-ForcePlatform without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k