90 open source boards using the HX711
Real designs built with the HX711, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
View base
scottbez1
81.2 × 81.2 mm81 parts2LApache-2.022.2kAVR/Arduino
Z-probe on smd resistors-2512
IvDm
15.3 × 19.3 mm17 parts2LGPL-3.0150ESP32
SmartKnob DevKit Base
SeedLabs-it
81.2 × 81.2 mm222 parts4LApache-2.047ESP8266
Forcegauge
szbeni
60 × 40 mm69 parts2LGPL-3.018ESP32
Lora node esp32 smd GPS
Christophe45
71.1 × 109.2 mm32 parts2LNo license14OpenEDM-wire tensioner
OpenEDM
60 × 77.4 mm24 parts2LNo license12STM32
Pedals
janc18
86 × 62 mm116 parts4LGPL-3.010ESP32
Crimpdeq
crimpdeq
23 × 63.8 mm46 parts2LCustom license9Load cell ampfilier-HX711-board hardware design
SolderedElectronics
22 × 22 mm18 parts2LTAPR-OHL-1.08Nordic nRF
Scale hx711
IoTReady
70 × 40 mm75 parts2LNo license7AVR/Arduino
Bertha main
Hackuarium
100 × 87 mm155 parts2LNo license6STM32
EcoApi BeeHiveMonitoring
EcoApi
90.6 × 58 mm166 parts2LGPL-3.04STM32
Lre avio daq2
IITB-Rocket-Team-Avionics
4.5 × 13.4 mm136 parts2LMIT4ESP32
The-Surevival
Rishaan2202
51 × 23 mm72 parts2LNo license3View base
Pytonballoon810
81.2 × 81.2 mm81 parts2LApache-2.02NXP
UniversalNode
DPIclimate
121.5 × 127.9 mm76 parts2LMIT2ESP32
Wifi voltmeter
makerspacelt
40 × 65 mm48 parts2LCERN-OHL-S-2.02STM32
Volumepad electronics
PhiMaii
110 × 80 mm169 parts4LNo license1AVR/Arduino
Phmeter
Hackuarium
100 × 87 mm145 parts2LCustom license1ESP32
ESP32-S3-WROOM-1-Custom-PCB-Design
jenna2004jna
101 × 101 mm117 parts4LNo license1STM32
FOC Control Boards
coopjz
81 × 80.9 mm106 parts4LMIT1HX-board
calstar
63.5 × 72.3 mm101 parts2LCC0-1.01AVR/Arduino
Load cell ampfilier-HX711-board with easy-C-hardware design
SolderedElectronics
38 × 22 mm25 parts2LTAPR-OHL-1.01RP2040/RP2350
Pulse echo azimuthal scanner
Jerome-Graves
100 × 65 mm14 parts2LMIT1- schematic only · 31 partsESP32
Urine analyzer lite
Sid93
31 parts2LNo license1 - schematic only · 28 partsESP32
Hydroponic veggie garden
Gregovate
28 partsMIT1 - schematic only · 16 partsAVR/Arduino
RotorRig-V1.0
GrzegorzG7
16 partsCC-BY-NC-4.01 STM32
Factory in a box
klaus-liebler
188 × 65 mm264 parts4LNo license0AVR/Arduino
Truss
practable
114.3 × 102.9 mm198 parts2LAGPL-3.00ESP32
Battery
86kkd
56.6 × 33.7 mm139 parts6LNo license0ESP8266
Wiscale hw
makerspacelt
100 × 50 mm107 parts2LNo license0RP2040/RP2350
CC3501-project hardware
enolf
85 × 56 mm105 parts4LNo license0ESP32
Grip strength meter
houseofbigseals
99 × 60 mm97 parts4LNo license0View base
camerakang
81.2 × 81.2 mm81 parts2LApache-2.00View base
Konn1nn
81.2 × 81.2 mm81 parts2LMIT0View base
DxnnySch
81.2 × 81.2 mm81 parts2LApache-2.00
How designs wire the HX711
Read from the KiCad layouts of 72 open source designs, one per repository: what each pin of the HX711 connects to, and the resistors, capacitors and other passives placed on it.
- The INA+ pin has a series resistor on 60 of 71 designs, most often 100 Ω (then 1 kΩ).
- The VBG pin has a capacitor to GND on 59 of 71 designs, most often 100 nF (then 1 µF).
- The INA- pin has a series resistor on 59 of 71 designs, most often 100 Ω (then 1 kΩ).
- The INA- pin has a series capacitor on 58 of 71 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSUPpin 1 | Connected to: 3.3V 83% |
|
| AVDDpin 3 | Connected to: A connector 21% · 3.3V 17% |
|
| VFBpin 4 | Connected to: Signal 92% |
|
| AGNDpin 5 | Connected to: GND 86% | — |
| VBGpin 6 | Connected to: Signal 94% |
|
| INA-pin 7 | Connected to: Signal 99% |
|
| INA+pin 8 | Connected to: Signal 100% |
|
| XOpin 13 | Connected to: Not connected 96% | — |
| XIpin 14 | Connected to: GND 88% | — |
| DVDDpin 16 | Connected to: 3.3V 93% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include View base by scottbez1, Z-probe on smd resistors-2512 by IvDm, SmartKnob DevKit Base by SeedLabs-it and Bed occupancy by thorio.
The HX711 in open source designs
The gallery holds 90 open source boards using the HX711 from 78 GitHub repositories; a typical one measures about 81.2 × 70 mm and carries around 68 components.
86% are two-layer designs, the rest use four layers or more, and 59% carry an open source license.
The most starred is View base by scottbez1.
Parts used alongside the HX711
Microcontrollers on boards using the HX711
What boards using the HX711 are built for
HX711: common questions
Where can I find a HX711 reference design?
Each of the 90 boards on this page is a real design using the HX711. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the HX711 INA+ pin?
The INA+ pin has a series resistor on 60 of 71 designs, most often 100 Ω (then 1 kΩ). Counted from the KiCad layouts of 72 open source designs using the HX711.
How is the HX711 VBG pin connected?
The VBG pin has a capacitor to GND on 59 of 71 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 72 open source designs using the HX711.
What resistor goes on the HX711 INA- pin?
The INA- pin has a series resistor on 59 of 71 designs, most often 100 Ω (then 1 kΩ). Counted from the KiCad layouts of 72 open source designs using the HX711.
What parts are used alongside the HX711?
The MT6701-CT, SN74LV1T34DBV, TMC6300, VEML7700 and AP2114HA-3.3 appear in the most repositories here.
Which microcontrollers do boards using the HX711 use?
Most are built on ESP32 (28), AVR/Arduino (10), STM32 (8) and ESP8266 (5).
How big is a typical board using the HX711?
The median is 81.2 × 70 mm, and 86% are two-layer designs.
What is the most popular open source board using the HX711?
By GitHub stars, View base by scottbez1, with 22,165 stars.
Can I simulate one of these boards using the HX711 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.