ESP32
ankitanandchoudhary2006-eng·ESP32·PCB/ESP32DEV.kicad_pcb
About the ESP32 PCB
ESP32 is an open source ESP32 PCB design by ankitanandchoudhary2006-eng, published on GitHub. It is a 2-layer board measuring 52 × 29 mm, with 26 components from 16 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the CH340C and AMS1117-3.3. By type, the board carries 7 resistors, 6 capacitors, 3 ICs, 3 connectors, 3 diodes and 2 transistors.
It belongs with the usb & debug tools designs in this gallery.
From the project
So I made a custom devboard based on ESp-Wroom-32 . It has a USB-C for power and signal and has interval voltage regulator to regulate the voltage down to 3.3V prior to that we have onboard LEDs and USB to UART circuit and it has 2 sets of 15 connectors that connectes to power ,
So I made a custom devboard based on ESp-Wroom-32 . It has a USB-C for power and signal and has interval voltage regulator to regulate the voltage down to 3.3V prior to that we have onboard LEDs and USB to UART circuit and it has 2 sets of 15 connectors that connectes to power , gnd and multiple pins on the ESP32.
Main components on the ESP32
ESP32 bill of materials (BOM)
26 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 2 | SS8050 | SOT-23 | Q1, Q2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 2 | Conn_01x15_Pin | PinHeader_1x15_P2.54mm_Vertical | J2, J3 |
| 2 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | B5819W | D_SOD-123 | D1 |
| 1 | RED | LED_0603_1608Metric | D2 |
| 1 | BLUE | LED_0603_1608Metric | D3 |
| 5 | 100nF | C_0603_1608Metric | C1, C3, C4, C5, C6 |
| 1 | 10uF/16V | CP_EIA-3216-10_Kemet-I | C2 |
| 2 | 5K1 | R_0603_1608Metric | R1, R2 |
| 1 | 1K | R_0603_1608Metric | R3 |
| 3 | 10K | R_0603_1608Metric | R4, R5, R6 |
| 1 | 220R | R_0603_1608Metric | R7 |
ESP32 design files
The KiCad project lives in the ankitanandchoudhary2006-eng/ESP32 repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/ESP32DEV.kicad_pcb
- SchematicPCB/ESP32DEV.kicad_sch
- BOMBOM.csv
ESP32: common questions
What microcontroller does the ESP32 use?
The ESP32 is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the ESP32 PCB?
The ESP32 measures 52 × 29 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32?
26 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32 design files?
From the ankitanandchoudhary2006-eng/ESP32 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32 design in my own project?
The repository has no license, so all rights stay with ankitanandchoudhary2006-eng. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k