STM32-Walkie-Talkie
ANSHUMANDOCX·STM32-Walkie-Talkie·PCB/STM32 Walkie Talkie.kicad_pcb
About the STM32-Walkie-Talkie PCB
STM32-Walkie-Talkie is an open source STM32 PCB design by ANSHUMANDOCX, published on GitHub. It is a 2-layer board measuring 55 × 45 mm, with 69 components from 37 distinct parts.
Its main chip is the STM32F411RET6, from the STM32 family. Other key parts include the AI-THINKER-RA-02, MAX98357A, MAX9814, NOKIA5110_LCD COPY and MIC5219-3.3YM5. By type, the board carries 25 capacitors, 17 resistors, 8 ICs, 6 diodes, 5 connectors and 3 inductors.
It belongs with the rf & radio, audio and power & battery designs in this gallery.
From the project
This is a Walkie talkie made using STM32 and LoRa
A custom walkie-talkie built on a bare STM32F411RET6 microcontroller and SX1278 LoRa radio module, designed from scratch in KiCad with a fully custom PCB.
- Push-to-talk (PTT) voice transmission over LoRa - Nokia 5110 display showing TX/RX status, RSSI, battery %, charging state - LED indicators for TX and RX - PWM buzzer with distinct tones for PTT, incoming call, low battery, charging complete etc - Battery percentage via voltage divider on ADC - Load sharing circuit — runs on USB power while charging battery - TP4056 charging status readable by firmware - SWD debug header for ST-Link V2…
Main components on the STM32-Walkie-Talkie
STM32-Walkie-Talkie bill of materials (BOM)
69 components, 37 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F411RET6 | LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | AI-THINKER-RA-02 Ai-Thinker-Ra-02 | Ai-Thinker-Ra-01-LoRa | U2 |
| 1 | MAX98357A | TQFN-16-1EP_3x3mm_P0.5mm_EP1.23x1.23mm | U3 |
| 1 | MAX9814 | TDFN-14-1EP_3x3mm_P0.4mm_EP1.78x2.35mm | U4 |
| 1 | NOKIA5110_LCD COPY | JST_XH_B8B-XH-A_1x08_P2.50mm_Vertical | U5 |
| 1 | MIC5219-3.3YM5 | SOT-23-5 | U6 |
| 1 | TP4056-42-ESOP8 | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U7 |
| 1 | DW01A | SOT-23-6 | U8 |
| 1 | ~ | TSSOP-8_L4.4-W3.0-P0.65-LS6.4-BL-2 | Q1 |
| 1 | AO3401A | SOT-23 | Q2 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mm | Y1 |
| 1 | MIC | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | STM32 Header | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | USB_C_RECEPTACLE_POWERONLY_6P USB_C_Receptacle_PowerOnly_6P | USB_C_Receptacle_GCT_USB4125-xx-x_6P_TopMnt_Horizontal | J3 |
| 2 | PTT | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4, J5 |
| 1 | Speaker | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | LS1 |
| 1 | SW_Push | SW_SPST_TS-1088-xR025 | SW1 |
| 5 | LED | LED_0603_1608Metric | D1, D2, D3, D4, D5 |
| 1 | SS34 | D_SMA | D6 |
| 1 | 120R | R_0603_1608Metric | FB1 |
Show 17 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | FerriteBead | R_0603_1608Metric | FB2, FB3 |
| 9 | 100N 100n | R_0603_1608Metric | C1, C2, C3, C4, C5, C6, C9, C16 +1 |
| 2 | 1u | R_0603_1608Metric | C7, C8 |
| 2 | 2.2UF 2.2uF | C_0805_2012Metric | C10, C21 |
| 5 | 0.1UF 0.1uF | R_0603_1608Metric | C11, C12, C23, C24, C25 |
| 1 | 0.47UF 0.47uF | R_0603_1608Metric | C13 |
| 2 | 220PF 220pF | R_0603_1608Metric | C14, C15 |
| 1 | 10UF 10uF | C_0805_2012Metric | C18 |
| 2 | 12PF 12pF | R_0603_1608Metric | C19, C20 |
| 1 | 470PF 470pF | R_0603_1608Metric | C22 |
| 3 | 1K | R_0603_1608Metric | R1, R14, R15 |
| 3 | 2K | R_0603_1608Metric | R2, R3, R4 |
| 2 | 100K | R_0603_1608Metric | R5, R6 |
| 1 | 150K | R_0603_1608Metric | R7 |
| 1 | 2.2K | R_0603_1608Metric | R8 |
| 5 | 100R | R_0603_1608Metric | R9, R10, R11, R12, R13 |
| 2 | 5.1K | R_0603_1608Metric | R16, R17 |
STM32-Walkie-Talkie design files
The KiCad project lives in the ANSHUMANDOCX/STM32-Walkie-Talkie repository on GitHub; these links point at the commit this page was built from.
STM32-Walkie-Talkie: common questions
What microcontroller does the STM32-Walkie-Talkie use?
The STM32-Walkie-Talkie is built around the STM32F411RET6, from the STM32 family.
How big is the STM32-Walkie-Talkie PCB?
The STM32-Walkie-Talkie measures 55 × 45 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the STM32-Walkie-Talkie?
69 components, from 37 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the STM32-Walkie-Talkie design files?
From the ANSHUMANDOCX/STM32-Walkie-Talkie repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the STM32-Walkie-Talkie design in my own project?
The repository has no license, so all rights stay with ANSHUMANDOCX. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the STM32-Walkie-Talkie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k