Zenith ir

arielhone·zenith-ir·hardware/kicad/MeshControl IR V1.1.kicad_pcb

Zenith ir PCB layout, top view — open source ESP32 board by arielhone

About the Zenith ir PCB

Zenith ir is an open source ESP32 PCB design by arielhone, published on GitHub. It is a 2-layer board measuring 70.2 × 45.5 mm, with 39 components from 21 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3, CH340C and TSOP41XX. By type, the board carries 13 capacitors, 9 resistors, 4 ICs, 4 test points, 4 diodes and 3 transistors.

From the project

A custom 2-layer board that turns an ESP32-S3 into a room IR controller: it drives IR LEDs strong enough to reach an air conditioner across the room, receives and decodes IR from original remotes (learn mode), measures room temperature, and is flashed over a single USB-C cable.

A custom 2-layer board that turns an ESP32-S3 into a room IR controller: it drives IR LEDs strong enough to reach an air conditioner across the room, receives and decodes IR from original remotes (learn mode), measures room temperature, and is flashed over a single USB-C cable.

- IR LEDs are switched by a MOSFET, not driven from a GPIO. An ESP32 pin can source roughly 40 mA, while an IR LED needs 100 mA+ pulses for real range. Q3 (2N7002) switches two LD271 LEDs in series from the 5 V rail, so the LED current comes from USB, not from the MCU. Running the two LEDs in series doubles the light…

Zenith ir, from the project README
From the project README

Main components on the Zenith ir

Zenith ir bill of materials (BOM)

39 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AMS1117-3.3
U1
1
ESP32-S3-WROOM-1
U2
1
CH340C
U3
1
TSOP41XX
TSOP41xx
U4
3
2N7002
Q1, Q2, Q3
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
4
TestPoint
TP3, TP4, TP5, TP6
1
DS18B20
temperaturesensor1
2
LD271
D1, D2
1
LED
D3
1
PRTR5V0U2X
D4
3
100U
100u
C1, C3, C9
8
100N
100n
C2, C4, C5, C6, C8, C11, C12, C13
1
10U
10u
C7
1
22U
22u
C10
2
5.1K
R1, R2
2
10K
R3, R4
2
100
R5, R6
1
47K
R7
1
47
R8
Show 1 more
QtyPartRefs
1
4.7K
4.7k
R9

Zenith ir design files

The KiCad project lives in the arielhone/zenith-ir repository on GitHub; these links point at the commit this page was built from.

Zenith ir: common questions

What microcontroller does the Zenith ir use?

The Zenith ir is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Zenith ir PCB?

The Zenith ir measures 70.2 × 45.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Zenith ir?

39 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Zenith ir design files?

From the arielhone/zenith-ir repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Zenith ir design in my own project?

The repository has no license, so all rights stay with arielhone. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Zenith ir without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards