Pcb
auto-watering·pcb
About the Pcb
Pcb is an open source ESP32 PCB design by auto-watering, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 188 × 91.4 mm, with 46 components from 8 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. Other key parts include the PC817. By type, the board carries 12 diodes, 12 resistors, 7 ICs and 6 relays.
From the project
Auto watering PCB KiCad project
KiCad project for auto watering PCB. This PCB is designed for up to 6 valves.
This KiCad project requires Espressif KiCad Library.
You can find a firmware designed to run on this board on the dedicated repository.
- ESP32 DevKit C - Support for ESP32 board - For each valve: - SRD12VDC relay - EL817(D)-G or PC817 C photocoupler - LED - JST connector 1x02 2.50mm pitch (for case mounted LED) - 1 kOhm resistor - 56 Ohm resistor - flyback diode - TerminalBlock Phoenix MKDS-1,5/2 1x02 5mm pitch (for valve) - Valves themselves (for example RainBird HV series, 24VAC) - 5V DC power supply for ESP32…

Main components on the Pcb
Pcb bill of materials (BOM)
46 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | PC817 | DIP-4_W7.62mm | U1, U2, U3, U4, U5, U6 |
| 1 | ESP32-DevKitC | ESP32-DevKitC | U7 |
| 9 | Conn_01x02 | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | 5VDC1, 12VDC1, 24VAC1, B1, B2, B3, B4, B5 +1 |
| 6 | SRD12VDC | Relay_SPDT_SANYOU_SRD_Series_Form_C | K1, K2, K3, K4, K5, K6 |
| 6 | LED | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | D1, D2, D3, D4, D5, D6 |
| 6 | 1N4004 | D_DO-41_SOD81_P10.16mm_Horizontal | D7, D8, D9, D10, D11, D12 |
| 6 | 1K | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R3, R5, R7, R9, R11 |
| 6 | 56 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R4, R6, R8, R10, R12 |
Pcb design files
The KiCad project lives in the auto-watering/pcb repository on GitHub; these links point at the commit this page was built from.
- Layoutauto_watering.kicad_pcb
- Schematicauto_watering.kicad_sch
Pcb: common questions
What microcontroller does the Pcb use?
The Pcb is built around the ESP32-DevKitC, from the ESP32 family.
How big is the Pcb?
The Pcb measures 188 × 91.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pcb?
46 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pcb design files?
From the auto-watering/pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pcb design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which auto-watering chose for the repository.
Can I test firmware for the Pcb without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k