Windpup
barzamin·windpup·pcb/windpup/windpup.kicad_pcb
About the Windpup PCB
Windpup is an open source ESP32 PCB design by barzamin, published on GitHub. It is a 2-layer board measuring 50.3 × 46.2 mm, with 38 components from 22 distinct parts.
Its main chip is the ESP-C3-WROOM-02, from the ESP32 family. Other key parts include the MAX3237, TLV1117-33, TLC59211 and TPD2E2U06. By type, the board carries 14 capacitors, 9 diodes, 5 ICs, 5 resistors, 3 connectors and 2 switches.
From the project
doggy of the valley of the wind
Main components on the Windpup
Windpup bill of materials (BOM)
38 components, 22 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MAX3237 | SSOP-28_5.3x10.2mm_P0.65mm | U1 |
| 1 | TLV1117-33 | TO-252-3_TabPin2 | U2 |
| 1 | ESP-C3-WROOM-02 | ESP-WROOM-02 | U3 |
| 1 | TLC59211 | TSSOP-20_4.4x6.5mm_P0.65mm | U4 |
| 1 | TPD2E2U06 | SOT-563 | U5 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_GCT_USB4085 | J1 |
| 1 | Conn_ARM_JTAG_SWD_10 | PinHeader_2x05_P1.27mm_Vertical_SMD | J2 |
| 1 | DB25_Female | DSUB-25_Female_EdgeMount_P2.77mm | J3 |
| 1 | push | SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | SW_SPDT | NidecCopal_CL-SB-12B-xx | SW2 |
| 8 | LED_Small | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D3, D4, D5, D6, D7, D8 |
| 1 | ESD9B5.0ST5G | D_SOD-923 | D9 |
| 2 | 22p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | 10u | CP_EIA-3528-12_Kemet-T_Pad1.50x2.35mm_HandSolder | C3, C6 |
| 1 | 100u | CP_EIA-7343-31_Kemet-D_Pad2.25x2.55mm_HandSolder | C4 |
| 3 | 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C13, C14 |
| 5 | 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8, C10, C11, C12 |
| 1 | 0.22u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 2 | 5.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | R_Pack08 | R_Cat16-8 | RN1 |
Windpup design files
The KiCad project lives in the barzamin/windpup repository on GitHub; these links point at the commit this page was built from.
Windpup: common questions
What microcontroller does the Windpup use?
The Windpup is built around the ESP-C3-WROOM-02, from the ESP32 family.
How big is the Windpup PCB?
The Windpup measures 50.3 × 46.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Windpup?
38 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Windpup design files?
From the barzamin/windpup repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Windpup design in my own project?
The repository has no license, so all rights stay with barzamin. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Windpup without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k