Raccoon HAT v1 — PoE Ethernet Tap
About the Raccoon HAT v1 — PoE Ethernet Tap
Raccoon HAT v1 — PoE Ethernet Tap is an open source PCB design by BenjiTrapp, published on GitHub. It is a 2-layer board measuring 65 × 56 mm, with 41 components from 35 distinct parts.
Other key parts include the SI3402-B-FS, TPS54302DDCR, RTL8153B-VB-CG, AP2112K-3.3TRG1 and W25Q16JVSSIQ. By type, the board carries 19 capacitors, 8 resistors, 5 ICs, 3 connectors, 2 LEDs and 1 crystal.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Red Team hardware implant — RPi4/CM4 inline Ethernet tap with PoE, dual cover identities (Cisco Phone / HP Printer), 802.1X NAC bypass, and Sliver C2
Red Team network hardware implant built on a Raspberry Pi 4 with a custom PCB HAT, running ParrotOS (ARM64). Designed for authorized penetration testing engagements.
The Raccoon Implant is an inline Ethernet tap that bridges two network ports on a custom HAT and captures traffic transparently while providing remote C2 access. The entire device is powered via PoE from the upstream switch port. It presents itself as either a Cisco IP Phone or an HP network printer to blend into enterprise infrastructure.
Main components on the Raccoon HAT v1 — PoE Ethernet Tap
Raccoon HAT v1 — PoE Ethernet Tap bill of materials (BOM)
41 components, 35 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SI3402-B-FS SI3402-B | QFN-20_U1 | U1 |
| 1 | TPS54302DDCR TPS54302 | SOT-23-6_U2 | U2 |
| 1 | RTL8153B-VB-CG RTL8153B | QFN-48_U3 | U3 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 | SOT-23-5_U4 | U4 |
| 1 | W25Q16JVSSIQ W25Q16 | SOIC-8_U5 | U5 |
| 1 | 25MHZ 25MHz | Crystal_3215 | Y1 |
| 1 | HR911105A 2x20 GPIO | PinHeader_2x20_P2.54mm | J1 |
| 1 | HR911105A | RJ45_HR911105A | J2 |
| 1 | USB-A 3.0 | USB-A_3.0_SMD | J3 |
| 1 | NSMD050-24V 500mA | PTC_1206 | F1 |
| 1 | 750342460 | Transformer_T1 | T1 |
| 1 | 19-217/GHC-YR1S2/3T Green | LED_0603 | LED1 |
| 1 | 19-217/Y2C-CQ2R2L/3T Amber | LED_0603 | LED2 |
| 1 | SRN6045TA-100M 10uH | Inductor_1210 | L1 |
| 1 | CL21A106KOQNNNG 100uF 63V | C_0805 | C1 |
| 1 | CL21A106KOQNNNG 10uF 25V | C_0805 | C2 |
| 1 | UVR1H101MDD1TD 100nF | C_0402 | C3 |
| 1 | UVR1H101MDD1TD 22uF 10V | C_0805 | C4 |
| 1 | CL05B104KO5NNNC 100nF BOOT | C_0402 | C5 |
| 2 | CL05B104KO5NNNC 10uF | C_0603 | C6, C8 |
Show 15 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | CL05B104KO5NNNC 100nF | C_0402 | C7, C9, C10 |
| 1 | CL21A226MQQNNNG 10uF | C_0603 | C11 |
| 1 | CL21A226MQQNNNG 100nF | C_0402 | C12 |
| 2 | CL05C100JB5NNNC 15pF | C_0402 | C13, C14 |
| 2 | 100nF | C_0402 | C15, C17 |
| 1 | 4.7uF | C_0603 | C16 |
| 1 | 100nF DVDD12 | C_0402 | C18 |
| 1 | 10uF DVDD12 | C_0603 | C19 |
| 1 | RC0402FR-0725K5L 24.9k | R_0402 | R3 |
| 1 | RC0402FR-0749K9L 5.36k | R_0402 | R4 |
| 2 | RC0402FR-0710KL 330R | R_0402 | R5, R6 |
| 1 | RC0402FR-071KL 25.5k | R_0402 | R7 |
| 1 | RC0402FR-071KL 10k | R_0402 | R8 |
| 1 | RC0402FR-07100KL 10k | R_0402 | R9 |
| 1 | RC0402FR-0719K1L 10k RST | R_0402 | R10 |
Raccoon HAT v1 — PoE Ethernet Tap design files
The KiCad project lives in the BenjiTrapp/TrashPandaPaws repository on GitHub; these links point at the commit this page was built from.
Raccoon HAT v1 — PoE Ethernet Tap: common questions
How big is the Raccoon HAT v1 — PoE Ethernet Tap?
The Raccoon HAT v1 — PoE Ethernet Tap measures 65 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Raccoon HAT v1 — PoE Ethernet Tap?
41 components, from 35 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Raccoon HAT v1 — PoE Ethernet Tap design files?
From the BenjiTrapp/TrashPandaPaws repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Raccoon HAT v1 — PoE Ethernet Tap design in my own project?
The repository has no license, so all rights stay with BenjiTrapp. Use it as a reference, and ask the author before reusing the design.
More boards in TrashPandaPaws
Similar boards
Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675
Radioberry preamp
65 × 56 mm137 parts2LNo license675
Hat
65 × 56 mm81 parts2LNo license675
Sram dev board
Wren6991
50 × 50 mm12 parts2LNo license508
ESP32
Chrismettal
66.4 × 48.1 mm20 parts2LCC-BY-SA-4.0446
ESP32
66.4 × 48.1 mm20 parts2LCC-BY-SA-4.0446