41 open source boards using the TPS54302DDCR
Real designs built with the TPS54302DDCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Moss
metrox-eth
82 × 79 mm208 parts4LApache-2.0116STM32
Mynd Main
teufelaudio
75 × 136 mm560 parts4LCC-BY-SA-4.076USB-C PD 5V supply — development
rjwalters
100 × 65 mm47 parts4LMIT74STM32
Ducker-Charger
Angelussss
66.4 × 163.6 mm256 parts4LCC-BY-NC-4.018Raccoon HAT v1 — PoE Ethernet Tap
BenjiTrapp
65 × 56 mm41 parts2LNo license4STM32
Mynd Main
Prototype-Fund-Hardware
75 × 136 mm560 parts4LNo license3R3 power
druzvv-hash
160 × 80 mm156 parts4LNo license1STM32
AxxSolder hw
ITGuyFromIA2
39 × 71 mm84 parts2LNo license1STM32
BMW-F20-AHU-CAN-Relay
Richard-CRT
56.7 × 45.1 mm58 parts4LNo license1Aesa
tieziyun
192 × 315.1 mm2040 parts4LNo license0After
DD1SB
180 × 140 mm287 parts2LMIT0ESP32
HX6-Miner
IsSasoriDev
170 × 115 mm258 parts6LGPL-3.00AIPE 48V to 24V / 1kW
FulongLi
300 × 220 mm220 parts6LNo license0ESP32
Solar
DinosaurPotato534
149.6 × 65 mm201 parts2LNo license0ESP32
Micromouse
MukeshSethy
100 × 120 mm177 parts4LNo license0RP2040/RP2350
Universal nixie display
kuvychko
100 × 85 mm155 parts2LMIT0STM32
Flight-Controller-V2
desanv01
40.6 × 50.5 mm115 parts6LCERN-OHL-S-2.00Crab robot
triluongmh-byte
110 × 80 mm113 parts4LNo license0WCH CH32/CH55x
Module-I2C-picohub-MOD-0011
buildwithnoknok
80 × 40 mm113 parts2LMIT0ESP32
Embedded projects
dashonigkuchen
63 × 73.2 mm85 parts6LMIT0NXP
4runner-Seat-Heat
alorman
74.4 × 71.5 mm72 parts2LNo license0STM32
FC-DRON-P3
Lucas-el-pato
40.7 × 40.7 mm71 parts6LNo license0Xmas hub
MRobertEvers
80 × 66 mm60 parts2LNo license0STM32
Pd sniffer
Badbird5907
63.8 × 44 mm40 parts2LNo license0C64-USB-C-PD-Power-Adapter
mamejay
46.1 × 30 mm39 parts2LCC-BY-NC-4.00- schematic only · 49 partsRaspberry Pi
Raspberry pi nas filesystem
jnwajei22
49 partsNo license0 Before
DD1SB
180 × 140 mm287 parts2LMIT0AIPE SiC Buck Power
FulongLi
240 × 180 mm213 parts4LNo license0STM32
Flight controller
DinosaurPotato534
149 × 65 mm155 parts2LNo license0ProPrj BLDCcontroller 2025-09-27
BrookDawn
40 × 40 mm53 parts4LNo license0Dfm-2oz
DD1SB
180 × 140 mm287 parts2LMIT0AIPE SiC Buck Control
FulongLi
120 × 80 mm187 parts4LNo license0RADIAN Panel / Interface
KrasForge
180.5 × 108 mm59 parts4LMIT0Dfm special finish
DD1SB
180 × 140 mm287 parts2LMIT0RADIAN Panel / Interface
KrasForge
180.5 × 108 mm59 parts4LMIT0E2-native
DD1SB
180 × 140 mm287 parts2LMIT0
How designs wire the TPS54302DDCR
Read from the KiCad layouts of 27 open source designs, one per repository: what each pin of the TPS54302DDCR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a series capacitor on 25 of 27 designs, most often 100 nF.
- The SW pin has a inductor on 24 of 27 designs, most often 10 µH (then 15 µH).
- The FB pin has a resistor to GND on 24 of 27 designs, most often 13.3 kΩ (then 10 kΩ).
- The BOOT pin has a series capacitor on 23 of 27 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 96% | — |
| SWpin 2 | Connected to: Signal 96% |
|
| VINpin 3 | Connected to: VSYS1 70% · a signal 30% |
|
| FBpin 4 | Connected to: Signal 96% |
|
| ENpin 5 | Connected to: Signal 81% |
|
| BOOTpin 6 | Connected to: Signal 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Moss by metrox-eth, Mynd Main by teufelaudio, USB-C PD 5V supply — development by rjwalters and Ducker-Charger by Angelussss.
The TPS54302DDCR in open source designs
The gallery holds 41 open source boards using the TPS54302DDCR from 28 GitHub repositories; a typical one measures about 115 × 96.5 mm and carries around 177 components.
50% are two-layer designs, the rest use four layers or more, and 49% carry an open source license.
The most starred is Moss by metrox-eth.
Parts used alongside the TPS54302DDCR
Microcontrollers on boards using the TPS54302DDCR
What boards using the TPS54302DDCR are built for
TPS54302DDCR: common questions
Where can I find a TPS54302DDCR reference design?
Each of the 41 boards on this page is a real design using the TPS54302DDCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS54302DDCR SW pin connected?
The SW pin has a series capacitor on 25 of 27 designs, most often 100 nF. Counted from the KiCad layouts of 27 open source designs using the TPS54302DDCR.
What resistor goes on the TPS54302DDCR FB pin?
The FB pin has a resistor to GND on 24 of 27 designs, most often 13.3 kΩ (then 10 kΩ). Counted from the KiCad layouts of 27 open source designs using the TPS54302DDCR.
How is the TPS54302DDCR BOOT pin connected?
The BOOT pin has a series capacitor on 23 of 27 designs, most often 100 nF. Counted from the KiCad layouts of 27 open source designs using the TPS54302DDCR.
What parts are used alongside the TPS54302DDCR?
The USBLC6-2SC6, AP2112K-3.3TRG1, BQ25713RSNR, ADS1115IDGSR and BMP388 appear in the most repositories here.
Which microcontrollers do boards using the TPS54302DDCR use?
Most are built on STM32 (9), ESP32 (5), WCH CH32/CH55x (1) and NXP (1).
How big is a typical board using the TPS54302DDCR?
The median is 115 × 96.5 mm, and 50% are two-layer designs.
What is the most popular open source board using the TPS54302DDCR?
By GitHub stars, Moss by metrox-eth, with 116 stars.
Can I simulate one of these boards using the TPS54302DDCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.