Starbie project
BeshoyHanna-BH·starbie-project·PCB/starbie.kicad_pcb
About the Starbie project PCB
Starbie project is an open source ESP32 PCB design by BeshoyHanna-BH, published on GitHub. It is a 2-layer board measuring 97.9 × 96.1 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the sensors designs in this gallery.
From the project
A tiny desk pet on a custom-designed PCB. An animated pixel creature lives on a 128x64 OLED, reacts when you tilt or shake the board, and can be napped, played with, fed and petted through a tilt-controlled radial menu. A DHT11 sensor adds room temperature and humidity.
A tiny desk pet on a custom-designed PCB. An animated pixel creature lives on a 128x64 OLED, reacts when you tilt or shake the board, and can be napped, played with, fed and petted through a tilt-controlled radial menu. A DHT11 sensor adds room temperature and humidity.
The board outline is bat-shaped, and the pet itself is a hand-made 32x32 bat sprite.
Built for Half Life by Hack Club. See JOURNAL.md for the build log and BOM.md for the parts list.
Main components on the Starbie project
Starbie project bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10K | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Starbie project design files
The KiCad project lives in the BeshoyHanna-BH/starbie-project repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/starbie.kicad_pcb
- SchematicPCB/starbie.kicad_sch
Starbie project: common questions
What microcontroller does the Starbie project use?
The Starbie project is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie project PCB?
The Starbie project measures 97.9 × 96.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie project?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starbie project design files?
From the BeshoyHanna-BH/starbie-project repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starbie project design in my own project?
The repository has no license, so all rights stay with BeshoyHanna-BH. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie project without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k