Esp32-led controller
BilginistAdam·esp32-led-controller·hardware/ledctl.kicad_pcb
About the Esp32-led controller PCB
Esp32-led controller is an open source ESP32 PCB design by BilginistAdam, published on GitHub under the MIT license. It is a 2-layer board measuring 64 × 38 mm, with 32 components from 26 distinct parts.
Its main chip is the ESP32-C3-WROOM-02-N4, from the ESP32 family. Other key parts include the AP63203WU. By type, the board carries 9 resistors, 8 capacitors, 4 connectors, 4 diodes, 2 ICs and 2 switches.
It belongs with the iot & wireless designs in this gallery.
From the project
12–24 V LED şeritleri WiFi üzerinden açıp kapatan ve PWM ile dimleyen küçük bir kontrol kartı. Proje KiCad donanım dosyalarını, iki firmware seçeneğini (ESPHome / PlatformIO) ve 3D yazıcıyla basılabilen bir kutuyu içerir.
12–24 V LED şeritleri WiFi üzerinden açıp kapatan ve PWM ile dimleyen küçük bir kontrol kartı. Proje KiCad donanım dosyalarını, iki firmware seçeneğini (ESPHome / PlatformIO) ve 3D yazıcıyla basılabilen bir kutuyu içerir.
- Kontrol: ESP32-C3-WROOM-02 (WiFi + BLE). Programlama dahili USB üzerinden USB-C ile yapılıyor, ayrı bir USB-UART çipi yok. - Giriş: 12–24 V DC. PTC sigorta ve TVS ile korunuyor. AP63203 buck regülatör 3.3 V üretiyor. - Besleme: D1/D2 diyotlarıyla kart adaptörden ya da sadece USB'den beslenebiliyor, yani programlarken adaptör gerekmiyor. - LED sürme: LED şeridini low-side…

Main components on the Esp32-led controller
Esp32-led controller bill of materials (BOM)
32 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP63203WU | TSOT-23-6 | U1 |
| 1 | ESP32-C3-WROOM-02-N4 ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U2 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | C480516 DC_IN_12-24V | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | C480516 LED_STRIP | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J2 |
| 1 | C165948 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 1 | C2337 UART | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | PTC_3A_hold_30V | Fuse_1812_4532Metric | F1 |
| 1 | TS-1187A RESET | SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | TS-1187A BOOT/USER | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | SS34 | D_SMA | D1 |
| 1 | SS14 | D_SMA | D2 |
| 1 | SMAJ28A | D_SMA | D3 |
| 1 | C72043 GREEN | LED_0603_1608Metric | D4 |
| 1 | 4.7UH 4.7uH_3A | L_Changjiang_FNR4030S | L1 |
| 1 | C13585 10uF_50V | C_1206_3216Metric | C1 |
| 1 | C14663 100nF_50V | C_0603_1608Metric | C2 |
| 2 | C14663 100nF | C_0603_1608Metric | C3, C7 |
| 2 | C45783 22uF_10V | C_0805_2012Metric | C4, C5 |
| 1 | C15850 10uF | C_0805_2012Metric | C6 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C15849 1uF | C_0603_1608Metric | C8 |
| 4 | C25804 10k | R_0603_1608Metric | R1, R2, R3, R4 |
| 1 | C22775 100R | R_0603_1608Metric | R5 |
| 1 | C25803 100k | R_0603_1608Metric | R6 |
| 1 | C21190 1k | R_0603_1608Metric | R7 |
| 2 | C23186 5.1k | R_0603_1608Metric | R8, R9 |
Esp32-led controller design files
The KiCad project lives in the BilginistAdam/esp32-led-controller repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/ledctl.kicad_pcb
- Schematichardware/ledctl.kicad_sch
- BOMhardware/BOM.csv
Esp32-led controller: common questions
What microcontroller does the Esp32-led controller use?
The Esp32-led controller is built around the ESP32-C3-WROOM-02-N4, from the ESP32 family.
How big is the Esp32-led controller PCB?
The Esp32-led controller measures 64 × 38 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-led controller?
32 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-led controller design files?
From the BilginistAdam/esp32-led-controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-led controller design in my own project?
Yes, under the terms of its MIT license, which BilginistAdam chose for the repository.
Can I test firmware for the Esp32-led controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k