92 open source boards using the AP63203WU
Real designs built with the AP63203WU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Cheetah-MX4-Mini
KaiPereira
81.6 × 88.8 mm165 parts4LCERN-OHL-P-2.0179RP2040/RP2350
OSS Radio Hardware Design
Arkos-Engineering
55 × 100.5 mm218 parts4LNo license75RP2040/RP2350
Pro rev1
TheRetroWeb
102.6 × 107.3 mm130 parts4LCERN-OHL-P-2.058USB-C-Power-Delivery-Breadboard-Power-Supply
bytesizedengineering
54 × 38 mm41 parts4LNo license20AVR/Arduino
SparkAltBatteryBoard
fahreddinaykut
58.8 × 29 mm37 parts4LMIT20ESP32
Esp32-recirc pump controller
pdw-mb
43.6 × 43.6 mm32 parts2LNo license17STM32
Hermes-FlightController
aadilnaji
51.4 × 51.4 mm64 parts4LMIT16ESP32
Paperflux
albanpetit
33.5 × 50 mm43 parts4LNo license16STM32
TRNXSDR-carrier
acruxcz
91.8 × 139.8 mm702 parts6LCERN-OHL-S-2.015ESP32
A3 8p redFIS
tothpetiszilard
124 × 40 mm77 parts2LAGPL-3.015GameConsoleV2
ThroatyMumbo
200 × 150 mm38 parts4LMIT15ESP32
Esp32-s3 single motor & battery controller
techy-robot
44.9 × 42 mm101 parts4LCERN-OHL-S-2.012RP2040/RP2350
Pico2-test mule
mikesmitty
52.5 × 42 mm68 parts2LCERN-OHL-P-2.012Nordic nRF
Locust
hlord2000
133.4 × 44.5 mm33 parts2LCERN-OHL-P-2.07ESP32
Avalanche32
AronASzucs
137 × 84 mm81 parts2LNo license3- schematic only · 70 partsESP32
ESP32-Geiger-Counter
AronASzucs
70 partsNo license3 ESP32
IoT Gateway STM32F407VGTx
minhtenlado
146.1 × 112.6 mm184 parts6LNo license2STM32
ROBRO
louismeuret
60 × 60 mm122 parts4LNo license2ESP32
ESP32 Breakouts Playground
PockyBum522
203.1 × 108.1 mm116 parts2LMIT2ESP32
Mini-AI-Camera-Module
bartsil
25 × 25 mm60 parts4LApache-2.02STM32
AratMicro
vorlaxen-labs
80 × 87.6 mm102 parts4LMIT1ESP32
Vertical wind turbine
Franzelfx
100 × 80 mm81 parts4LNo license1STM32
DAQ-V4.1
IlyaasAitSimmou
38 × 100 mm76 parts4LNo license1ESP32
Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation
subbuu-aadhii
100 × 100 mm69 parts4LMIT1STM32
Stomper
JoKhannn
40.3 × 39.2 mm64 parts4LNo license1ESP32
PCB
Pegoku
70 × 104.5 mm46 parts2LGPL-3.01ESP32
Ekspander 100x i2c
kanaboid
500 × 108.8 mm264 parts4LNo license0STM32
VNA Project
fdreshaj
200 × 200 mm220 parts6LNo license0ESP32
PLC4UNI
paulmartinezcuenta
5 × 5 mm177 parts4LMIT0Nordic nRF
CLABSI
Nick-Trigger
56.5 × 57 mm151 parts6LNo license0ESP32
Accoustic Sensing Node
irocobble
93.9 × 49.8 mm105 parts2LNo license0ESP32
Prototyp
Huruvarshan
160 × 100 mm98 parts4LMIT0STM32
BallBalncer
MarcelKleiner
64.5 × 77 mm98 parts2LNo license0WCH CH32/CH55x
CACKLE-PSU-2s 40A PSU and charger
techy-robot
45 × 20 mm95 parts4LCC-BY-NC-4.00ESP32
Tesla sextant BT
Pepa1ZdepaDotC
100 × 100 mm90 parts4LNo license0STM32
Tiny pov
usedhondacivic
250 × 30.5 mm88 parts2LNo license0
How designs wire the AP63203WU
Read from the KiCad layouts of 73 open source designs, one per repository: what each pin of the AP63203WU connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a series capacitor on 69 of 73 designs, most often 100 nF (then 10 µF).
- The SW pin has a inductor on 66 of 73 designs, most often 4.7 µH (then 3.9 µH).
- The BST pin has a series capacitor on 64 of 73 designs, most often 100 nF (then 10 µF).
- The FB pin is tied to 3.3V on 55 of 73 designs (a signal on 17).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| FBpin 1 | Connected to: 3.3V 75% · a signal 23% |
|
| GNDpin 4 | Connected to: GND 99% | — |
| SWpin 5 | Connected to: Signal 90% |
|
| BSTpin 6 | Connected to: Signal 97% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Cheetah-MX4-Mini by KaiPereira, MiniSpeedCam-1.2 by Valar-Systems, OSS Radio Hardware Design by Arkos-Engineering and Power supply by sbstnh.
The AP63203WU in open source designs
The gallery holds 92 open source boards using the AP63203WU from 78 GitHub repositories; a typical one measures about 64.8 × 60 mm and carries around 66 components.
53% use four copper layers or more, and 43% carry an open source license.
The most starred is Cheetah-MX4-Mini by KaiPereira.
Parts used alongside the AP63203WU
Microcontrollers on boards using the AP63203WU
What boards using the AP63203WU are built for
AP63203WU: common questions
Where can I find a AP63203WU reference design?
Each of the 92 boards on this page is a real design using the AP63203WU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP63203WU SW pin connected?
The SW pin has a series capacitor on 69 of 73 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 73 open source designs using the AP63203WU.
How is the AP63203WU BST pin connected?
The BST pin has a series capacitor on 64 of 73 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 73 open source designs using the AP63203WU.
How is the AP63203WU FB pin connected?
The FB pin is tied to 3.3V on 55 of 73 designs (a signal on 17). Counted from the KiCad layouts of 73 open source designs using the AP63203WU.
What parts are used alongside the AP63203WU?
The USBLC6-2SC6, AP63205WU, ESP32-S3-WROOM-1, MPU-6050 and BMP280 appear in the most repositories here.
Which microcontrollers do boards using the AP63203WU use?
Most are built on ESP32 (46), STM32 (18), RP2040/RP2350 (7) and Nordic nRF (3).
How big is a typical board using the AP63203WU?
The median is 64.8 × 60 mm, and 47% are two-layer designs.
What is the most popular open source board using the AP63203WU?
By GitHub stars, Cheetah-MX4-Mini by KaiPereira, with 179 stars.
Can I simulate one of these boards using the AP63203WU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.