79 open source boards using the ESP32-C3-WROOM-02-N4
Real designs built with the ESP32-C3-WROOM-02-N4, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Terrarium Control Board
justbuchanan
140 × 140 mm51 parts2LApache-2.0270ESP32
Endeavour2
petrmikheev
100 × 85 mm263 parts6LGPL-3.049ESP32
OpenAirScope
emertcakir
100 × 75 mm247 parts4LMIT26ESP32
Current logger
hnz1102
50 × 70 mm64 parts2LNo license18ESP32
PCB-Mini-Environmental-Sensor
MbFredys
25.1 × 25.2 mm32 parts2LCERN-OHL-W-2.013ESP32
Mini current meter
hnz1102
30 × 43 mm38 parts2LNo license10ESP32
Temp logger
hnz1102
50 × 70 mm52 parts2LNo license5ESP32
Po midi adapter
Hanz-Tech
75.3 × 71 mm51 parts2LNo license5ESP32
CoralWave
mineiwik
54.1 × 21.9 mm45 parts2LMIT5ESP32
UPLC-Digital
fredriknk
31.4 × 22 mm41 parts4LMIT5ESP32
UPLC-Analog
fredriknk
31.4 × 22 mm48 parts4LMIT4ESP32
Wakepcbox
hnz1102
40 × 60 mm45 parts2LNo license4ESP32
Launch-Party-Badge-Software
poorawsanhsirk
178 × 110 mm404 parts4LNo license3ESP32
Mini power
hnz1102
46 × 54 mm49 parts2LNo license3ESP32
Capsicum
hutscape
70 × 55 mm61 parts2LNo license2ESP32
RGB-LED-and-High-Dencity-CCT-Controller
MbFredys
88.2 × 70.2 mm53 parts2LCERN-OHL-W-2.02ESP32
Remote
EwoudVV
27.9 × 66.1 mm12 parts2LNo license2RP2040/RP2350
Aster2350
Amronos
80 × 65 mm121 parts4LApache-2.01ESP32
ESP32Sensor
LESA-RPI
154.1 × 74 mm94 parts4LNo license1ESP32
Nex
dialgorithm
35 × 39 mm60 parts2LNo license1ESP32
AttentioLight-1 Mainboard1
engemil
50 × 50 mm56 parts4LCERN-OHL-P-2.01ESP32
Electropulse
Shehroz30
50 × 50 mm51 parts4LMIT1ESP32
ZEGAR-ESP32
Fese673
54.1 × 21.9 mm45 parts2LNo license1ESP32
PranRakshak
SrivarsanK
52 × 88 mm45 parts2LNo license1ESP32
SlimeVR board 2-5W
Skaut0071
61 × 50 mm36 parts2LCERN-OHL-P-2.01ESP32
Vscp smart han port interface
grodansparadis
44.5 × 34.5 mm24 parts2LNo license1ESP32
Lfp
maxakash
216 × 146 mm831 parts2LNo license0ESP32
IOT-project
datnguyenhcmut
100 × 75 mm247 parts4LMIT0ESP32
Custom round pcb led flash
xmyoot
84 × 84 mm224 parts4LNo license0ESP32
Ee115-capstone
tsaimatthew
115.8 × 98.6 mm187 parts2LNo license0ESP32
RadRail-Badge
SharKingStudios
75 × 100 mm146 parts2LNo license0RP2040/RP2350
Tspico hardware
factus10
130 × 64.3 mm144 parts4LCERN-OHL-S-2.00ESP32
Export board
zeugmaster
60 × 110 mm127 parts4LCERN-OHL-S-2.00ESP32
Microohmetro uis
EDWARDPJ26
64 × 116 mm93 parts4LNo license0ESP32
Airquality
MorgenWebDigital
45 × 95 mm76 parts2LCustom license0ESP32
Wind controller
lindestad
70 × 64 mm70 parts2LMIT0
How designs wire the ESP32-C3-WROOM-02-N4
Read from the KiCad layouts of 59 open source designs, one per repository: what each pin of the ESP32-C3-WROOM-02-N4 connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a pull-up to 3.3V on 51 of 59 designs, most often 10 kΩ (then 5.1 kΩ).
- The 3V3 pin is tied to 3.3V on 57 of 59 designs.
- The IO8 pin has a pull-up to 3.3V on 44 of 59 designs, most often 10 kΩ (then 5.1 kΩ).
- The EN pin has a capacitor to GND on 41 of 59 designs, most often 1 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 3V3pin 1 | Connected to: 3.3V 97% | — |
| ENpin 2 | Connected to: A connector 24% |
|
| IO8pin 7 | Connected to: Signal 83% · not connected 17% |
|
| IO9pin 8 | Connected to: A connector 24% |
|
| GNDpin 9, 19 | Connected to: GND 92% | — |
| IO2pin 16 | Connected to: Signal 78% · not connected 22% |
|
12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Terrarium Control Board by justbuchanan, Endeavour2 by petrmikheev, OpenAirScope by emertcakir and Current logger by hnz1102.
The ESP32-C3-WROOM-02-N4 in open source designs
The gallery holds 79 open source boards using the ESP32-C3-WROOM-02-N4 from 59 GitHub repositories; a typical one measures about 68 × 65 mm and carries around 51 components.
66% are two-layer designs, the rest use four layers or more, and 56% carry an open source license.
The most starred is Terrarium Control Board by justbuchanan.
Parts used alongside the ESP32-C3-WROOM-02-N4
Microcontrollers on boards using the ESP32-C3-WROOM-02-N4
What boards using the ESP32-C3-WROOM-02-N4 are built for
ESP32-C3-WROOM-02-N4: common questions
Where can I find a ESP32-C3-WROOM-02-N4 reference design?
Each of the 79 boards on this page is a real design using the ESP32-C3-WROOM-02-N4. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP32-C3-WROOM-02-N4 EN pin?
The EN pin has a pull-up to 3.3V on 51 of 59 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 59 open source designs using the ESP32-C3-WROOM-02-N4.
How is the ESP32-C3-WROOM-02-N4 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 57 of 59 designs. Counted from the KiCad layouts of 59 open source designs using the ESP32-C3-WROOM-02-N4.
What pull-up resistor is used on the ESP32-C3-WROOM-02-N4 IO8 pin?
The IO8 pin has a pull-up to 3.3V on 44 of 59 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 59 open source designs using the ESP32-C3-WROOM-02-N4.
What parts are used alongside the ESP32-C3-WROOM-02-N4?
The USBLC6-2SC6, AP2112K-3.3TRG1, MCP73831-2-OT, SGP41-D-R4 and SPX3819M5-L appear in the most repositories here.
Which microcontrollers do boards using the ESP32-C3-WROOM-02-N4 use?
Most are built on ESP32 (67) and RP2040/RP2350 (12).
How big is a typical board using the ESP32-C3-WROOM-02-N4?
The median is 68 × 65 mm, and 66% are two-layer designs.
What is the most popular open source board using the ESP32-C3-WROOM-02-N4?
By GitHub stars, Terrarium Control Board by justbuchanan, with 270 stars.
Can I simulate one of these boards using the ESP32-C3-WROOM-02-N4 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.