HardLabs

EMK310

Boilingtub·EMK310·KiCad/EMK310_P2_rev1/EMK310_P2_rev1.kicad_pcb

EMK310 PCB layout, top view — open source PIC board by Boilingtub

About the EMK310 PCB

EMK310 is an open source PIC PCB design by Boilingtub, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 80 × 100 mm, with 50 components from 18 distinct parts.

Its main chip is the PIC18F45K22, from the PIC family. Other key parts include the Opamp_Quad, Opamp_Dual and MCP2221AxP. By type, the board carries 20 resistors, 8 connectors, 8 capacitors, 4 ICs, 3 transistors and 1 LED.

From the project

Repository to hold Code For EMK310 Group 55

RB0 - USB-to-UART RST RB1 - RB2 - RB3 - MOTOR2B RB4 - RB5 - Capacitive Touch Sensor RB6 - RB7 - LEDB

RC0 - LEDR RC1 - LEDG RC2 - (CCP1) MOTOR1B RC3 - SCL 1 RC4 - SDA 1 RC5 - Sensor 2 RC6 - Sensor 1 RC7 - Sensor 0

RD0 - SCL2 RD1 - SDA2 RD2 - Sensor 5 RD3 - Sensor 4 RD4 - RD5 - RD6 - TX RD7 - RX

RE0 - MOTOR2F RE1 - RE2 - MOTOR1F RE3 - PROGRAMMING PIN

Main components on the EMK310

PIC18F45K22Opamp_QuadOpamp_DualMCP2221AxP

EMK310 bill of materials (BOM)

50 components, 18 distinct parts.

QtyPartRefs
1
PIC18F45K22
U1
1
Opamp_Quad
U2
1
Opamp_Dual
U3
1
MCP2221AxP
U4
3
VP0610L
Q1, Q2, Q3
2
Conn_01x20_Socket
J1, J4
3
Conn_01x02_Socket
J2, J3, J7
1
Conn_01x05_Socket
J5
1
Conn_01x04_Socket
J6
1
USB_A
J8
1
~
PR1
5
R_Potentiometer
RV1, RV2, RV3, RV4, RV5
1
LTS-6980HR
AFF1
4
C_Small
C1, C2, C3, C4
1
10uF
C5
3
0.22uF
C6, C7, C8
17
R
R16, R17, R18, R19, R20, R21, R22, R23 +9
3
10k
R33, R34, R35

EMK310 design files

The KiCad project lives in the Boilingtub/EMK310 repository on GitHub; these links point at the commit this page was built from.

EMK310: common questions

What microcontroller does the EMK310 use?

The EMK310 is built around the PIC18F45K22, from the PIC family.

How big is the EMK310 PCB?

The EMK310 measures 80 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the EMK310?

50 components, from 18 distinct parts. The full bill of materials is listed on this page.

Where can I download the EMK310 design files?

From the Boilingtub/EMK310 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the EMK310 design in my own project?

Yes, under the terms of its GPL-2.0 license, which Boilingtub chose for the repository.

Can I test firmware for the EMK310 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

Similar boards